Emerson Copeland Eazycool OLTE-82D-TFD Скачать руководство пользователя страница 44

Страница: 44 / 55

C6.1.9/0219/E

Appendix 1: Parameter list level 1 (Pr1)

Code

Description

Range

C07

Refrigerant selection for
regulation

R404A(0-404) - R507(1-507) - R134A(2-134) - R22(3-R22) -

R407C(4-07C) - R407A(5-07A) - R407F(6-07F) -

R448A(48A) - R449A(8-49A) - R410A(9-410)

8-R449A

C16

Digital compressor setpoint

C03 to C04

3.0

1.0

C17

Proportional band for
compressor regulation

0.1 to 9.9 bar; 0.1 to 99.9 PSI;

0.1°C to 25.5°C

2.0

1.0

C21

Cycle time for digital
compressor

10 to 40 sec

C24

Minimum capacity for digital
compressor

0 to C25

C27

Time with DGS at PMi
before switching off another
load

0 to 255 sec

D29

Low-pressure alarm value

A02 to A03

0.8

0.3

E66

Delta temperature
condenser floating setpoint

0.0°C to 25.5°C

8.0

N01

Current minute

0 to 59

N02

Current hour

0 to 23

N03

Day of month

1 to 31

N04

Month

1 to 12

N05

Year

0 to 99

T18

Access to Pr2 level

[0÷999]

3 2 1

Table 22: Parameters level 1

Содержание Copeland Eazycool OLTE-82D-TFD
























































Результаты поиска

Содержание Copeland Eazycool OLTE-82D-TFD

Отзывы:

Бренды по названию

Популярные бренды

Emerson Copeland Eazycool OLTE-82D-TFD, Инструкции по применению

Результаты поиска

Содержание Copeland Eazycool OLTE-82D-TFD

Отзывы:

Бренды по названию

Популярные бренды