background image

 

 

© 2017 Emerson Climate Technologies, Inc.

 

AE21-1355 R4 

 

Safety Instructions 
 

Digital Capacity Control for Copeland Discus

 refrigeration compressors ar

e manufactured according 

to the latest U.S. and European Safety Standards. Particular emphasis has been placed on the user's 
safety. Safety icons are explained below and safety instructions applicable to the products in this 
bulletin are grouped on Page 3. These instructions should be retained throughout the lifetime of the 
compressor. 

You are strongly advised to follow these safety instructions.

 

 

Safety Icon Explanation 

 

DANGER indicates a hazardous situation which, if not avoided, will result 
in death or serious injury. 
 
WARNING indicates a hazardous situation which, if not avoided, could 
result in death or serious injury. 
 
CAUTION, used with the safety alert symbol, indicates a hazardous 
situation which, if not avoided, could result in minor or moderate injury. 

 

NOTICE is used to address practices not related to personal injury. 

 

CAUTION, without the safety alert symbol, is used to address practices not 
related to personal injury. 

 

 
 
 
 
 
 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

DANGER

 

WARNING

 

CAUTION

 

NOTICE

 

CAUTION

 

Содержание COPELAND 3DSDR17ME-TFD












Отзывы: