background image

1. Securely attach the hanger bracket to the outlet

box using the two screws supplied with the outlet
box. (Figure 10.)

How to Hang

Your Ceiling Fan

TWO SCREWS
SUPPLIED WITH
OUTLET BOX

HANGER
BRACKET

TAB

OUTLET
BOX

Figure 2

AT LEAST

7'

CEILING

FLOOR

OUTLET
BOX

HANGER
BRACKET

HANGER BALL/
DOWNROD  ASSEMBLY

NOTE: CEILING COVER,
SUPPLY WIRES AND
FAN WIRES OMITTED
FOR CLARITY.

Figure 9

Figure 10

Figure 11

2. Carefully lift the fan and seat the hanger ball/

downrod assembly on the hanger bracket that was
just attached to the outlet box (Figure 11). Be sure
the groove in the ball is lined up with tab on the
hanger bracket (Figure 10).

The fan must be hung with at least 7' of clearance
from floor to blades (Figure 9).

WARNING

!

Hanger bracket must seat firmly against outlet box. If
the outlet box is recessed, remove wall board until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.

WARNING

!

To avoid possible fire or shock, do not pinch wires
between the hanger ball/downrod assembly and
hanger bracket.

WARNING

!

Failure to seat tab in groove could cause damage to
electrical wires and possible shock or fire hazard.

WARNING

!

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician in in doubt.

WARNING

!

The outlet box and joist must be securely mounted
and capable of supporting at least 50 lbs. Use only a
U.L. outlet box listed as “Acceptable for Fan
Support”.

WARNING

!

6

Electrical Requirements

The outlet box must be securely anchored and capa-
ble of withstanding a load of at least 50 pounds.

If your fan is to replace an existing ceiling light fixture,
turn electricity off at the main fuse box at this time and
remove the existing light fixture.

Your new ceiling fan will require a grounded electrical
supply line of 120 volts AC, 60 Hz, 15 amp circuit.

To avoid fire or shock, follow all wiring instructions
carefully.
Any electrical work not described in these instruc-
tions should be done or approved by a licensed
electrician.

WARNING

!

To reduce the risk of fire, electric shock, or personal
injury, mount fan to outlet box marked “Acceptable
for Fan Support”, and use screws supplied with
outlet box. Most outlet boxes commonly used for
support of light fixtures are not acceptable for fan
support and may need to be replaced. Consult a
qualified electrician in in doubt.

WARNING

!

Содержание CF935AB02













Отзывы: