Emerson AMS Скачать руководство пользователя страница 71

Страница: 71 / 92

7. Emerson recommends resetting the keying posts of removed CHARM Terminal

Blocks to prepare it for the installation of other CHARM types. For resetting the key
settings see

Installing CHARMs hardware

. The Thermocouple/mV Terminal Block

has a fixed key setting and cannot be reset.

6.3

Remove the Address Plug

Procedure

1. Flip down the CHARM labeling component (see

Figure 5-17

for location), if there is

one.

2. To remove the Address Plug, insert a flat-tip screwdriver into the latch of the

CHARM Address Terminal Block. See

Figure 5-16

for location of the latch.

3. Move the screwdriver down to unlock the Address Plug.
4. Pull the Address Plug out of the Address Terminal Block to remove it completely.

6.4

Remove the CHARM Address Terminal Block

The procedure is the same as for the CHARM Terminal Blocks. See

Remove a Terminal

Block

6.5

Remove the +24 V DC Power Module

CAUTION

Any work on the system may impair asset health monitoring and machine protection.

Procedure

1. To remove the +24 V DC Power Module, push the latch of the slot for the +24 V DC

Power Module upwards.
The +24 V DC Power Module is unlocked.

2. Pull the +24 V DC Power Module out of the slot to remove it completely.

Installation Guide

Removing CHARMs hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

Содержание AMS





























































































Результаты поиска

Содержание AMS

Отзывы:

Emerson AMS, Руководство по установке, Страница: 71 / 92

Результаты поиска

Содержание AMS

Отзывы: