Emerson AMS Скачать руководство пользователя страница 59

Страница: 59 / 92

5.5.1

Connect the input signal wiring – self-powered

Figure 5-11: Signal connection

A. Analog Input AI 4 to 20 mA CHARM

B. CHARM Baseplate

C. CHARM Terminal Block

D. Field device with analog output

E. Cable shield connection

Prerequisites

•

Wire cutter

•

Tool for removing the cable sheath

•

Wire stripper

•

Suitable screw driver for the CHARM Terminal Block screws

•

Observe the hints in

Wiring guidelines

Procedure

1. At opened door, lead the signal cable through a cable gland close to the slot where

the CHARM to be connected is installed.

2. Strip the cable sheath at a length of approximately 200 mm.
3. Strip each wire at a length of approximately 10 mm.
4. Connect the wires to the CHARM Terminal Block.

•

Connect terminal

of the analog output of the field device to terminal

of the

CHARM Terminal Block.

Installation Guide

Installing CHARMs hardware

MHM-97923-PBF

April 2020

MHM-97923-PBF, Rev. 1.0

Содержание AMS





























































































Результаты поиска

Содержание AMS

Отзывы:

Emerson AMS, Руководство по установке, Страница: 59 / 92

Результаты поиска

Содержание AMS

Отзывы: