EMC2 AX100 Series Скачать руководство пользователя страница 58

Страница: 58 / 68

AX100-Series - Installing a Fibre Channel Storage System with a Direct Connection to a NetWare Server

Configuring an Existing Storage System

7. Use the

Event Notification

page to configure the storage system

to send an E-mail message when the storage system encounters a
problem.

To display the Events Notification page -

In the Navisphere

Express navigation pane, under

System

, click

Settings

, and then

click

Event Notification

For details on configuring the storage system to send E-mail
messages, use the Navisphere Express Help Center.

8. Configure PowerPath:

/etc/opt/emcpower/powercf -q
powermt config

9. On the server, verify that PowerPath sees all the paths to the

virtual disks with the PowerPath command:

powermt display dev=all

What Next?

Go to

Preparing Virtual Disks to Receive Data

(page 61).

Configuring an Existing Storage System

Read this section if you are configuring an

existing

AX100SC or

AX100 storage system. An existing storage system is one that was
already connected to a server when you started the installation
procedure.

Before You Start

You need to complete the configuration planning worksheets from

Planning Your AX100-Series Fibre Channel Storage-System Configuration

in the "Plan" section on the AX100 support website or the

AX100-Series Documentation

CD.

Содержание AX100 Series





































































Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды

EMC2 AX100 Series, Руководство пользователя

Результаты поиска

Содержание AX100 Series

Отзывы:

Похожие инструкции для AX100 Series

Бренды по названию

Популярные бренды