EMC EMC VNX VNX5200 Скачать руководство пользователя

Страница: 13 / 18

Installing a DC-AC inverter

DC-Powered VNX™ Series Enclosures Installation and Operation Guide

Installing a DC-AC inverter

DC storage systems that support file I/O include 1U DC-AC inverters for the control
stations. Each control station connects to an inverter, which is in turn connected to
the DC power source.

Figure 4 on page 9

shows a typical VNX example; VNX II systems

typically install the inverters above the control stations, as shown in

Figure 5 on

page 10

To install a DC-AC inverter assembly, follow these steps:
1. From the front of the cabinet, insert the alignment pin on one mounting rail

assembly into the middle hole of the selected 1U space on a rear channel.

2. Extend the rail to the front cabinet channel. Align the holes of the front rail flange

to the inside of the channel, ensure the rail is level, and then install two M5 x 16
mm Phillips securing screws in the top and bottom holes.

Leave the screws slightly loose to allow for adjustment when you install the tray.
Do not insert a screw in the middle hole yet.

3. At the back of the cabinet, insert and tighten two M5 x 16 mm securing screws in

the holes above and below the alignment pin, as shown above. Repeat steps 1
through 3 for the other rail assembly.

EMC3253

Adjustable rail

Alignment pin

Front

Left front

Screw (2)

Mounting rail

Right rear

Screw (2)

Mounting rail

Alignment pin

Содержание EMC VNX VNX5200



















Результаты поиска

Содержание EMC VNX VNX5200

Отзывы:

Похожие инструкции для EMC VNX VNX5200

Бренды по названию

Популярные бренды

EMC EMC VNX VNX5200, Инструкция по установке и эксплуатации

Результаты поиска

Содержание EMC VNX VNX5200

Отзывы:

Похожие инструкции для EMC VNX VNX5200

Бренды по названию

Популярные бренды