V
/
Hz esp
:
See pump nameplate
.
Liquid temperature
:
4
~
50
Storage temperature
: -
10
~
Relativa Air Humidity
:
95
Max
.
+
50
.
AFS SERIES PUMPS
Installation
diagram
When installing and using this electrical equipment
,
basic safety
precautions should always be followed
,
including the following
:
IMPORTANT
SAFETY
INSTRUCTIONS
1) READ AND FOLLOW ALL
INSTRUCTIONS
2 WARNING
)
To reduce the risk of injury
.
do not permit children to use this product
unless they are closely supervised at all
times
.
3
.
WARNING
Risk of Electrical Shock
.
Connected only to grounding type rece
-
ptacle protected by a ground fault circuit
interrupter
(
GFCI
).
Contact a qualified
electrician if you cannot verify that the
receptacle is protected by GFCI
.
4 CAUTION
Do not bury cord. Locate
)
cord to minimize abuse from lawnmowers
,
hedge trimmers
,
and other equipment
.
5 CAUTION
)
In case the running
parts will injure people
,
don
'
t make
the electric pump running before then
pipeline have been connected
.
6 WARNING
)
To reduce the risk of
electrical shock
,
replace damaged
cord immediately
.
7 WARNING
)
To reduce the risk of
electrical shock
,
do not use extension
cord to connect unit electric supply
;
provide a properly located outlet
.
8 CAUTION
)
Jetpump for jetted bathtubs
,
spapools
,
swimmingpools
,
massage
stations
,
cleaning system
.
9
)
Do not install within an outer encl
-
osure or beneath the skirt of a hot tub
unless so marked
.
10) This appliance is not intended for use
by young children or infirm persons unless
they have been adequately supervised by
a responsible person to ensure that they
can use the appliance safely
.
11
)
Young children should be supervi
-
sed to ensure that they do not play with
the appliance
.
12 SAVE
THESE
INSTRUCTIONS
)
SWIMMING TRAINING PUMP
INSTRUCTION
MANUAL
1) General
These instructions are for correct installation
,
and optimum performance of the Bath
pumps
,
so they should be read carefully
.
These are single
-
stage centrifugal pumps
designed to operate with compact hydromassage equipment
,
They are equipped with
a total
-
emptying system to prevent the discharge of residual liquid in each stopping
.
These units are designed to operate with clean water at a maximum water temperature
of 50°C
.
Built of top quality materials
,
they are subjected to strict hydraulic and electrical
controls and are carefully verified
.
Correct installation is ensured by following these
instructions and those of the wiring diagram
;
otherwise
,
over loads may be produced in
the motor
.
We decline responsibility for any damage caused by not following these
instructions
.
180
280
430
245
215
E
77
319
163
95
E
Model
Qmax
3
(
m
/
h
)
Hmax
(
m
)
90
17
.
5
AFS40
78
13
E
3
G2
/
4
or
4FBT
Power
P1
(
kW
)
4
.
0
3
.
0
1-4
4-4
EMPU16022762
AFS55
Pump parts for AFS
Key No.
Part No.
Description
Qty
1
89023501
Union
2
2
89023502
Screw with Nut & Washer
6
3
01112094
Pump Body
1
4
02010251
O-Ring for Flange
1
5
89023503
Nut for Impeller
1
6
01271049
Impeller AFS40
1
6
01271050
Impeller AFS55
1
7
04015054
Mechanical Seal
1
8
89023504
Screw
4
9
01112095
Pump Flange
1
10
89023505
Screw
2
11
01112096
Base
1
12
01031040
Wire Box
1
13
02010265
Box Slinger
1
14
01031041
Fan
1
15
01031042
Fan cover
1
