manualshive.com logo in svg

EM TEST CWS 500A / 75, Руководство пользователя, Страница: 54 / 67

Поделиться
Скачать
EM TEST CWS 500A / 75 Скачать руководство пользователя страница 54

53

12.3.

Installed Files on your Hard Drive

The install path is Progdir = C:\EMTEST\ICD32

CDN     <DIR>

 

Directory for Calibration data

RESULT  <DIR>

 

Directory for Result data

TEST    <DIR>

 

Directory for Test data

ICD32    EXE
DEMO32   DLL
DIA32    DLL
DLOG32   DLL
COMP32   DLL
OWL52F   DLL
CW3230   DLL
BDS52F   DLL
ICD      HLP
VECTOR   CNF
ICD      BMP
ICD_V2   INI
ICD32    INI

PMM6600  MCF
HP5347   MCF
HP5347A2 MCF
KEITHL01 MCF
NRVD_1   MCF
NRVS     MCF
HP344011 MCF
EXAMPLE3 DOC
EXAMPLE2 DOC
EXAMPLE1 DOC
_DEISREG ISR
_ISREG32 DLL

Calibration data for any CDN’s included in the delivery is stored in the
directory "CDN" Copy this files from the Disk2 to the directory
Progdir\ICD32\CDN.

12.4.

Installation / Remove

Installatiom

1.  Start  MS-Windows and insert the ICD disk1 in the floppy drive.
2. 

Select in the Taskline  ”

START

” -> ”Execute”

3.  Start the program  

a:setup

4. Select 

the 

OK button

.

5.  Follow the instructions on the screen.

Remove

Select the directory

“Systemcontrol “
“-> Software”

“-> Characteristics of Software  

 ”

the title 

ICD32

.

Click to the button “Remove” for uninstall the software. Probably it is necessary to
remove some file in the directory "ICD32" with the File manager.

Содержание CWS 500A / 75




































































Отзывы:

Нет отзывов