ELTRA CS-2000 Скачать руководство пользователя страница 111 | Manualshive

Страница: 111 / 160

background image

Service

111

Pos : 7. 14 /0025 Übersc hrift en/ELTRA 1.1 Übersc hrift en/11 Gas pump replacement Eltra @ 8\ mod_1396941649931_9. doc x @ 60396 @ 2 @ 1

5.7 Gas pump replacement

Pos : 7. 15 /0010 ELTR A/ 0015 s ervic e_ins truc tions/C S-2000_s er vice/ 15 Ser vic e_C S-2000/1540 Modul G as pump r epl ac ement @ 9\ mod_1425543580653_9. doc x @ 74790 @ @ 1

Fig. 95: Gas pump

–

Switch off the analyzer and disconnect the mains power plug.

–

Disconnect plug (1) of the pump from the socket X4 on the board (2).

–

Disconnect the tubes (3) and (4) from the pump (5).

–

Remove the pump from the supporting panel (6) by pulling the four rubber buffers (7).

(If necessary they can be cut).

–

Reinstall a new pump in reverse order.

REMARK

For installing a new pump, the rubber buffers (7) of the new pump have to be pulled down from
underneath the supporting panel (6) by using slim pliers. If suitable pliers not available, the
board (2) can be removed by unscrewing the four nuts (8).

«
...
109
110
111
112
113
...
»

Содержание CS-2000

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CS-2000

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 16

Бренд: VeEX Страницы: 2

Бренд: Kawai Страницы: 19

Бренд: Calculated Industries Страницы: 64

Бренд: Camille Bauer Страницы: 62

Power Xpert PXM 4000

Бренд: Eaton Страницы: 28

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hammond Страницы: 16

Бренд: Nady Audio Страницы: 2

Бренд: National Instruments Страницы: 18

Бренд: Magene Страницы: 80

Бренд: FISCHER Страницы: 20

Бренд: H-Star Страницы: 36

Бренд: SBS Страницы: 17

Бренд: D-tect Systems Страницы: 28

Бренд: Oceanic Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды