manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 87 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 87

EK280 

Application Manual 

85 

 

7.3.3 

FE260 with internal analog modem (PSTN Modem) 

 
 
 

 

 
Modemadapterboard 73016717 V1.2 
with a connected telephone cable 
 

 
Insys analog modem 
module 

 

 

 

Figure 13: Insys Analog modem module in the FE260

 

 

 

 

 

 

 

La 

 

 

Lb 

 

 

 

 

La2 

 

 

Lb2 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This interface card is used as an interface for an analog telephone line. 

 

Prerequisites for process described below: 

 

The FE260 is connected and configured as described in chapter 7.3.1. 

 

7.3.3.1  Parametrization of the EK280 

i 

For parameterization of the EK280 you will require a connection cable for the optical interface as 
well as the enSuite application, which can be downloaded for free at www.elster-instromet.com. 

a) Closing the time windows 

In order that the parameterization works correctly the time windows 5 and 6 must be closed. To do this: 

 

Connect a PC with enSuite installed to the EK280 optical interface using the connection cable. 

 

Start enSuite and set up the communication link to the EK280. (see chapter 3.1 "Setting up the 
communication link to the EK280 via optical interface", page 15) 

 

Select "

Navigation

" on the left-hand side and then "

Parameterize online

" at the bottom of the 

navigation window.  

 

In the top of the device window open the path "

Parameters

" > "

Interfaces

" by clicking on the relevant 

plus signs, and then select "

Call time windows

". 

 

In call windows 5 and 6 set start and end to the same value for each one and then select the 
"Transfer changes to device" icon at the top of the enSuite window. 

 

Then wait a minute, for any communications activity in progress on the EK280 to be safely stopped. 

Содержание EK280




































































































































































Отзывы:

Нет отзывов