manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 37 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 37

EK280 

Application Manual 

35 

 

6.2 

NF pulse output (low-frequency) 

Each of the outputs 1 to 4 (terminals DA1 to DA4) can be programmed as a low-frequency pulse output. 

 

6.2.1 

Parameterization 

Parameterization is carried out via the keyboard on the EK280.  
Alternatively, parametrization can be carried out using the 

enSuite

 program. The paths which are subsequently 

described can be found in 

enSuite

 under "

Parameterize online

" > "

Parameters

". 

Setting up the output mode: 

 

Move the cursor to register "

Serv.

"and along the following path to the mode for the corresponding 

output 

"Md.O1" 

to

 "Md.O4"

: 

Serv. 

 Outputs 

 Output 1 

 Md.O1   

Serv. 

 Outputs 

 Output 2 

 Md.O2   

Serv. 

 Outputs 

 Output 3 

 Md.O3   

Serv. 

 Outputs 

 Output 4 

 Md.O4 

 

i 

The low-frequency pulse output of the EK280 can be operated with active or inactive logic. The 
output mode must be programmed accordingly for this purpose (see below). 

 

 

Press the ENTER 

 button. The actual parameterized value flashes.

 

 

Press one of the arrow buttons 

 or 

 until the 

"pulse+" 

(Logic active) or

 "pulse -"

 (Logic inactive) 

text flashes. 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key.

 

Setting up the source for the output:  

 

When in the corresponding menu press the

 button until 

"Sc.O1

", 

"

 

Sc.O2

", 

"

 

Sc.O3

", or 

"

 

Sc.O4

" is 

displayed. 

 

Press the ENTER 

 button. The actual parameterized value flashes. 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys to a value specified in the table.  

 

Sc.O… 

Description 

02:300_0 

Vb

 

Volume at base conditions (undisturbed) 

02:301_0 

VbD

 

Volume at base conditions (disturbed) 

02:302_0 

VbT  Volume at base conditions total (undis disturbed) 

04:300_0 

Vm

 

Volume at measurement conditions (undisturbed) 

04:301_0 

VmD

 

Volume at measurement conditions (disturbed) 

04:302_0 

VmT  Volume at measurement conditions total (undis disturbed) 

 

Press the ENTER button to confirm the value setting. Input can be canceled using the ESC key. 

Setting up the cp value for the output: 

 

i 

The cp value of an output states how many pulses were emitted per cubic meter. A cp value 
of 0.1/m3 (0.1 pulses per m3) means that e.g. a pulse is emitted per 10m3.

 

 

 

When in the corresponding menu press the 

 button until "

cp.O1

", "

cp.O2

", "

cp.O3

" or "

cp.O4

" is 

displayed. 

 

Press the ENTER 

 button. The actual parameterized value flashes. 

 

Move the cursor to the digits using the 

 or 

 arrow keys and update them using the 

 or 

 arrow 

keys to the desired cp value for the corresponding output. 

 

Press the ENTER button to confirm the set value. It is possible to abort the entry by pressing the 
ESC button. 

Содержание EK280




































































































































































Отзывы:

Нет отзывов