background image

 

Installation

, connection and commissioning 

25 

5.1.3 Installation on a wall 

 

Using the wall mounting feet (see appendix), install the EK205 on the wall.  

 

 

 

 

Ill.: 6

 

1.  Using the four self-cutting screws 

provided on the rear of the EK205

install the wall mounting feet. The 
fastening feet can be fastened in 
different positions.  

2.

 

Drill holes in the wall

 

in accordance 

with the position of the installed 
installation feet.

 

Select the wall plugs 

suitable for the size of the screws and 
insert them in the borings of the well. 

3.

 

Use four

 

screws for fastening the 

EK205, e.g. 5 x 35 mm. 

 

5.1.4 Three-way cock

7

 

When installing the pressure sensor, a three-way cock is usually installed in order to carry out 
an inspection of the pressure sensor in built-in condition or for the replacement of deficient 
sensors without deactivating the overall gas line. The three-way cock available from Elster 
has the following structure: 

 

 

 

The pipeline from the pressure sensor to the meter must be laid in a falling 
manner so that, where applicable, water cannot damage the pressure sensor 
or influence the measurement precision. 

 

 

                                                      

7

 Not applicable when using EK205 as a Temperature Conversion Device. 

 

Ill.: 7 

 1 

:

 

From the meter: From the pressure 
connection of the gas meter  
For bellow-type gas flow meters, this is 
carried out on the input side of the meter 

 2 

:

 

For the MU: To connect the gas sensor 
of the Volume Conversion Device 

 3 

:

 

Test connection: Possibility to take test 
pressure or to gibe external pressure on 
the pressure sensor of the Volume 
Conversion Device. 

 

When installing the three-way cock, it must be noted that the position of the 
operating lever is checked with the corresponding throughputs, as the lever 
can be removed and may be installed in a twisted manner. 

Prüfen mit

Betriebsdruck

B

e

trie

b

s-

ste

llu

n

g

P

fe

n

 m

it

F

rm

d

d

ru

ck

Absperrung

45° Stellung

Содержание EK205








































































Отзывы: