elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя | Manualshive

Страница: 7 / 68

background image

5

Description

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

1.

Description

The

Sensor Mini-Sewi KNX L-Pr

for the KNX building bus system captures bright-

ness and motion in rooms.

The

Sensor Mini-Sewi KNX TH-L-Pr

additionally

measures the temperature and the

air humidity and calculates the dew-point. Via the bus, the indoor sensor can receive
external values of temperature and humidity and process them further with its own
data to a total value (mixed value, e.g. room average). Integrated PI-controllers control
ventilation (humidification/dehumidification according to humidity) and heating/cool-
ing (according to temperature).

The

Sensor Mini-Sewi KNX TH-L-Pr

can output a warning to the bus as soon as the

comfort field, as per DIN 1946, is left. Actuating variable comparators can compare and
output variables that were received via communication objects.

All measurement values can be used for the control of limit-dependent switching out-
puts. States can be linked via AND logic gates and OR logic gates.

Functions:

•

Brightness measurement

with

brightness control

•

Motion detection

•

Threshold values

can be adjusted per parameter or via communication

objects

•

4 AND and 4 OR logic gates

, each with 4 inputs. All switching events as well

as 16 logic inputs (in the form of communications objects) can be used as
inputs for the logic gates. The output of each gate can be configured optionally
as 1-bit or 2 x 8-bit

Additional functions Mini-Sewi KNX TH-L-Pr:

•

Measuring the

temperature

and

air humidity

(relative, absolute), each with

mixed value calculation

. The share of internal measurement value and

external value can be set as a percentage

•

Bus message, whether the values for temperature and air humidity are within
the

comfort field

(DIN 1946).

Dew point

calculation

•

PI-controller for heating

(one or two-stage) and

cooling

(one or two-stage)

according to temperature. Regulation according to separate setpoints or basic
setpoint temperature

•

PI controller for humidity

according to humidity: Ventilate/Air (one-stage) or

Ventilate (one or two-stage)

•

2 actuation variable comparators

to output minimum, maximum or

average values. 5 inputs each for values received via communication objects

Configuration is made using the KNX software ETS. The

product file

can be down-

loaded from the Elsner Elektronik website on

www.elsner-elektronik.de

in the “Ser-

vice” menu.

1.0.1. Scope of delivery

•

Combined sensor

«
...
5
6
7
8
9
...
»

Содержание Mini-Sewi KNX L-Pr





































































Отзывы:

Нет отзывов

Похожие инструкции для Mini-Sewi KNX L-Pr

MyDlink DCH-S150

Бренд: D-Link Страницы: 8

Бренд: Abus Страницы: 353

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 14

Бренд: Abus Страницы: 11

Бренд: Abus Страницы: 110

Бренд: Abus Страницы: 82

Бренд: Abus Страницы: 18

Бренд: Abus Страницы: 18

Бренд: Abus Страницы: 16

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 101

Бренд: Abus Страницы: 33

Бренд: Abus Страницы: 99

Бренд: C-TEC Страницы: 10

Бренд: Ecco Страницы: 2

Бренд: Channel Vision Страницы: 2

Бренд: Zipato Страницы: 2

Бренд: Pulnix Страницы: 44

IQ PANEL 2 PLUS

Бренд: QOLSYS Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды