elsner elektronik Mini-Sewi KNX L-Pr Скачать руководство пользователя

Страница: 40 / 68

Parameter setting

Sensors Mini-Sewi KNX TH-L-Pr and Mini-Sewi KNX L-Pr

• Version: 30.08.2018 • Technical changes and errors excepted.

Block

The switching output can be blocked using an object.

If the block is activated, define specifications here for the behaviour of the output when
blocked.

The behaviour of the switching output on release is dependent on the value of the pa-
rameter "Switching output sends" (see "Switching output")

6.9.

Temperature PI control

The chapter "Temperature PI control" only applies to the TH-L-Pr
model.

Activate the control if you want to use it.

General control

Set, in which cases

setpoint values and extension time

received via object are to

be retained. The parameter is only taken into consideration if the setting via object is
activated below. Please note that the setting "After power supply restoration and pro-

Use switching output block

No • Yes

Analysis of the blocking object

• At value 1: block | At value 0: release
• At value 0: block | At value 1: release

Blocking object value before
1st communication

0 • 1

Behaviour of the switching output

On block

• Do not send message
• send 0
• send 1

On release
(with 2 seconds release delay)

[Dependent on the "Switching output
sends" setting]

Switching output sends on change

• Do not send message
• Send switching output status

Switching output sends on change to 1

• Do not send message
• if switching output = 1



send 1

Switching output sends on change to 0

• Do not send message
• if switching output = 0



send 0

Switching output sends on change and
periodically

Send switching output status

Switching output sends on change to 1
and periodically

if switching output = 1



send 1

Switching output sends on change to 0
and periodically

if switching output = 0



send 0

Use control

No • Yes

Содержание Mini-Sewi KNX L-Pr





































































Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды

elsner elektronik Mini-Sewi KNX L-Pr, Инструкция по установке и настройке

Результаты поиска

Содержание Mini-Sewi KNX L-Pr

Отзывы:

Похожие инструкции для Mini-Sewi KNX L-Pr

Бренды по названию

Популярные бренды