elsner elektronik 70550 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 52

elsner elektronik 70550 Скачать руководство пользователя страница 5

3

Safety and usage instructions

Actuator KNX S1R-B4 compact

• Version: 12.09.2022 • Technical changes and errors excepted.

1.

Safety and usage instructions

Installation, testing, operational start-up and troubleshooting should
only be performed by an authorised electrician.

DANGER!
Risk to life from live voltage (mains voltage)!

There are unprotected live components inside the device.

• Inspect the device for damage before installation. Only put undamaged
devices into operation.
• Comply with the locally applicable directives, regulations and provisions for
electrical installation.
• Immediately take the device or system out of service and secure it against
unintentional switch-on if risk-free operation is no longer guaranteed.

Use the device exclusively for building automation and observe the operating instruc-
tions. Improper use, modifications to the device or failure to observe the operating in-
structions will invalidate any warranty or guarantee claims.
Operate the device only as a fixed-site installation, i.e. only in assembled condition and
after conclusion of all installation and operational start-up tasks, and only in the sur-
roundings designated for it.
Elsner Elektronik is not liable for any changes in norms and standards which may occur
after publication of these operating instructions.

1.1. Safety notice for automatic functions

WARNING!
Risk of injury from automatically moving components!

Parts of the system can be started by the automatic controls
and be a danger to persons.
•

No persons may remain in the travelling range of parts
driven by an electric motor.

•

Adhere to the relevant building regulations.

•

Ensure that the return path/access to the building is not blocked
if spending time outside the building (danger of being locked out).

•

Correctly decommission the system for maintenance and
cleaning work.

If there is a power outage, the system does not work. Therefore, shadings should be
moved to a save position if there are anticipated weather conditions, for example, if
this has not already been done by the automatic function (product protection).

If the power supply is removed, the connected drive switches off. When the power is
restored, the consumer remains switched off until a new movement command is re-
ceived by the actuator.

«
...
3
4
5
6
7
...
»

Содержание 70550





















































Отзывы:

Нет отзывов