background image

18

ETS Database Parameters

Intelligent Power Supply KNX PS640-IP 2U

 • Version: 21.09.2021 • Technical changes and errors excepted.

Using the "Sending difference" function with the "Output voltage" is possible 
only within the "Alarm 1,2,3,4" tabs like described in chapter 3.7.

The "Output voltage" value is valid only if most of the load is on the KNX bus 
output

If the "Output current" value is < 10 mA, for calculations, the input voltage is 
assumed to be at 230 V AC

6.3. Maximum Tracking

With setting the "Tracking period" a certain period of time is tracked in order to find the
maximum observed value contained. After each expired period this value can be sent
over the bus. The maximum tracking function is available for the measurement
sources "Output current" and "Device Temperature".

Device temperature

Device temperature [°C]

disable • enable

Enable/disable group associations, measurement and following settings.

Sending difference

2...10 °C

Difference between actual and last sent value which triggers the sending.

Cyclic sending

disabled • 1 min • 2 min…5 min • 
10 min • 15 min…30 min • 1 h • 2 h…8 h

Info telegram is sent regularly.

Alarm settings

disable • enable

Enable/disable the alarm function.

Threshold

0…110 [°C]; 70

Select threshold value to execute the "Behaviour on alarm activation".

Hysteresis

0…40; 1 [°C]

Select hysteresis interval value to execute the "Behaviour on alarm deactivation".

Behaviour on alarm activation

• disabled
• send value 0
• send value 1
• set value to 0
• set value to 1

Select action on entering the threshold range.

Behaviour on alarm deactivation

• disabled
• send value 0
• send value 1
• set value to 0
• set value to 1

Select action on leaving the threshold (+hysteresis) range.

Tracking period [s]

10…32,000 [s]; 1,800

Determination of the time period for maximum value tracking.

Maximum value of Output current

Output current maximum [mA]

disable • enable

Содержание 70147



























Отзывы: