Elseta IOMOD HT Скачать руководство пользователя страница 5

Danger - important notice, which may affect the safety of the user or device.

Attention - notice on possible problems that may arise in individual cases.

Information Notice - the information that is useful advice or special places. 

Warning of the danger. The work may be performed only by a qualified professional. Equipment installation,

commissioning and maintenance may only be performed by a qualified professional. If the safety notes in this manual,

the term refers to persons qualified specialists authorized to perform commissioning, grounding and labeling devices,

systems and circuits. The person must: Be aware of occupational safety in the workplace. Need to understand the

equipment components. Electrical equipment. Have the knowledge and skills to identify a component beneath the

voltage. 

To maintain the equipment necessary to always turn off the power supply before installing or dismantling works. It

must be in mind that even though alone equipment, but can have a common ground connection. Always before

connecting the power supply, cables and interconnect components must be inspected. 

This product can not be implemented, or resold to install in areas that are high-security as nuclear power plants,

aircraft navigation, military equipment, transport traffic in management. In areas where equipment failure can result in

of nature and human injury. 

Do not operate the equipment in extreme weather conditions, as they may affect the operation of the equipment.

Equipment's Manual Uses Symbols

Содержание IOMOD HT















Отзывы: