manualshive.com logo in svg

Elmo st-I200, Руководство по обслуживанию, Страница: 29 / 40

Поделиться
Скачать
Elmo st-I200 Скачать руководство пользователя страница 29

SOUND (Cont'd)

Case

Step

Point

Remark

Magnetic recording 
cannot be effected

Recording knob 
assy

(P7-k)

Check the breakage of Recording knob assy by 
a tester.

AMP assy
(P7-j)

Check Sound head whether the adequate bias 
voltage has been effected.

If not, replace AMP assy.
*Bias voltage:

Single recording  .. 30-50V A.C.
Double recording .. 25-30V A.C.

Check the breakage of Tr3 in AMP assy to find 

out the damage of high frequency circuit in 
AMP assy.

If so, replace AMP assy.

Recording level is 
low

AMP assy
(P7-j)

Check the bias voltage of Sound head to find 
out under-bias current.

If so, replace AMP assy.

Sound head
(P5-56)

If Sound head has been exhausted or broken, 
replace Sound head.

P-18

Head presser

(P5-51)

If the film cannot be held in parallel with Head 

presser and Sound head, adjust the position of 
Head presser holder assy.

P-18

Film

If the sound track of film has been exhausted, 

replace film.

Output sound is low 
during optical 

recorded film 
reproduction

Exciter lamp
(P5-68)

Adjust the position of Exciter lamp if it has 
been distorted.

P-17

Sound lens

(P5-81)

Adjust the angle and position of Sound lens if it 

has been distorted.
If Sound lens has been stained, replace.

P-17

Silicon photo diode

(P5-77)

Check the breakage of Silicon photo diode and 

if so, replace.

P-17

AMP assy
(P7-j)

Check the output voltages on Circuit plate in 
comparison with the voltage checking points on 

AMP circuit plate and if the unusual voltage 
would be measured, replace AMP assy.

P-34

Film

Recording level of the film loaded is low.

- to be continued -

- 27 -

Содержание st-I200









































Отзывы:

Нет отзывов