Elmo st-I200 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 40

Elmo st-I200 Скачать руководство пользователя страница 27

MACHINE FRAME (Cont'd)

Case

Step

Point

Remark

Auto-threading
mechanism cannot

be released

Solenoid lever
(P4-32)

Adjust the position of Solenoid lever so that
Loop former lever assy may be released.

P-13

Film loop moves to
upper side

Lateral guide 1,2
(P3-35)

Increase the spring tension of lateral guide
spring to prevent the movement of film loop.

Slide plate

(P3- 39)

Bend Slide plate upward to prevent the

movement of film loop.

Lower film loop
cannot be performed

Fly wheel
(P5-24)

Increase the spring tension of Fly wheel spring.

Pad roller

(P5-64)

Adjust the position of Link lever spring so that

the tension of Pad roller may be increased.

P-16

Tension roller
(P5-63)

Move the position of Balance lever spring so
that the film may not be stretched downward

excessively.

P-16

Motor switch knob
cannot be turned

Reverse lever
(P6-20)

If Reverse lever has been interrupted and
deformed by AMP holder 2, replace or fix

Reverse lever and also cut off the portion of
AMP holder 2 to not interrupt the movement of

Reverse lever.

P-12

Film has been
feeded during still

projection

Clutch
mechanism

(P7-8)

Adjust the position of Clutch lever (1) assy, at
the same time, adjust the position of Clutch

link adjuster as well as Clutch lever (2) assy to
convey the rotation of Motor assy during both

18 f/s and 24 f/s projection.

P-10

- 25 -

«
...
25
26
27
28
29
...
»

Содержание st-I200









































Отзывы:

Нет отзывов