manualshive.com logo in svg

Elmo st-I200, Руководство по обслуживанию, Страница: 26 / 40

Поделиться
Скачать
Elmo st-I200 Скачать руководство пользователя страница 26

MACHINE FRAME (Cont'd)

Case

Step

Point

Remark

Lower film loop 
increases during 

forward projection

Middle gear 1, 2
(P5-35,36)

Replace either the damaged Middle gear 1 or 2.

Noise around 
Second sprocket 

during forward 
projection

Second sprocket
(P5-13)

If the sprocket teeth has been deformed, 
replace second sprocket.

P-14

Turn Second sprocket gradually to search the 

position where the noise is minimized.

Tension roller
(P5-63)

Move the position of Balance lever spring 1 by 
attaching plate to search the position where 

the noise is minimized.

P-16

Film passing is not 
smooth during 

auto-threading

Erasing head
(P5-58)

If the film is interrupted by Erasing head, 
adjust the position of Erasing head.

P-18

Sound drum

(P5-19)

If the film is interrupted by Sound drum, 

adjust the position of Head stand.

P-18

Head presser
(P5-51)

If the space between Head presser (1) assy and 
Head film guide either too wide or narrow and 

the film is interrupted around Head film guide, 
bend Head presser holder assy to adjust the 

space.

P-18

Film cannot pass 
through second 

sprocket during 
auto-threading

Film guide 3
(P5-74)

Adjust the position of Film guide 3 to pass the 
film smoothly.

P-16

Film does not wind 

on Reel during auto-
threading

Film guide 4

(P5-11)

If the film hits the edge of Reel, adjust the 

position of Film guide 4.

P-14

Take-up guide
(p5-3)

If the angle of Take-up guide with respect to 
Reel is distorted, bent Release switch presser 

to obtain the correct angle.

P-4

- to be continued -

- 24 -

Содержание st-I200









































Отзывы:

Нет отзывов