Elmo st-I200 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 40

Elmo st-I200 Скачать руководство пользователя страница 22

B. PROJECTION LAMP & LENS

Case

Step

Point

Remark

Lamp does not light Lamp

(P3-3)

Take out Lamp and check the defective of
Lamp itself.

If so, install new Lamp.

P-6

Lamp socket assy
(P3-2)

Take out Lamp, check the output terminals of
Lamp socket assy whether the voltage (approx.

A.C. 22-23V) would be applied.
If so, raise the output terminals of Lamp socket

assy to be in contact with Lamp.

P-6

Switch assy
(P6-i)

Check Micro switch SW9, SWIO whether would
work properly, also of which attaching screw

would be loosened.

P-12

Check the position of Lamp switch lever 1.
If not, replace or adjust.

Transformer

(P7-18)

Check both terminals of H.L. on Transformer

terminal whether the voltage would be applied.

P-8

Dark image

Lamp
(P3-3)

Check whether Lamp would be off the rim of
Lamp holder (2) assy.

P-6

To obtain the sufficient brightness, first loosen

attaching screws and move Lamp fixing plate
and Lamp holder (2) assy back and forth until

most bright screen can be achieved.

Safety shutter
(P7-ll)

If Safety shutter could not keep off from the
optical axis of the screen during Motor switch

knob positioned F or R, adjust the position of
Safety shutter.

P-10

Uneven screen

brightness

Lamp

(P3-3)

To obtain leveled brightness, first loosen

attaching screws and move back and forth until
most bright and leveled screen brightness can

be achieved.

P-6

Uneven screen
focusing

Projection lens
(P3-8)

To align the optical axis, first pass the focusing
test film and either tighten or loosen attaching

screw to obtain evenness in focusing.

P-7

- 20 -

«
...
20
21
22
23
24
...
»

Содержание st-I200









































Отзывы:

Нет отзывов