Elkron MP500/16 Скачать руководство пользователя страница 61

Страница: 61 / 140

MP500/4N-8-16 Programming

4.18.8.1

Programming procedure

Proceed as follows to program the GPRS parameters:

1) Enter

<Installer code>

, press

, then

and finally

repeatedly until TELEPHONE DIALER

appears.

2) Press

and then

several times until GPRS PARAMETERS appears.

3) Press

4) Press

. Enter the APN parameter setting on the keypad and press

to confirm.

5) Press

6) Press

. Enter the User setting on the keypad and press

to confirm.

7) Press

8) Press

. Enter the password setting on the keypad and press

to confirm.

9) Press

10) Press

. Enter the DNS1 setting on the keypad and press

to confirm.

11) Press

12) Press

. Enter the DNS2 setting on the keypad and press

to confirm.

13) Press

14) Press

. Enter the ACCESS NUMBER setting on the keypad and press

to confirm.

15) Press

repeatedly to exit from the menu.

4.18.9

IDP/IP parameters

The following parameters can be set to send alarms in IDP mode over IP, i.e. using the GPRS telephone interface or the IT500WEB
web server:



REM.CTRL CODE:

numeric field, max. 16 characters (min. 3 characters) containing the code which must be registered at the

alarm receiving centre.



CODE

RECEIVER:

numeric field, max. 6 characters (min. 1 character) containing the ID code of the alarm receiving centre

(optional).



SYSTEM CODE

: numeric field, max. 6 characters (min. 1 character) containing a further system ID code which must be registered

at the alarm receiving centre (optional).



ENABLE

ENCRYPT.:

parameter for enabling encrypted transmission. Select the encryption key length if encryption is enabled.



ENCRYPTION KEY:

hexadecimal field (from 0-9 and A-B-C-D-E-F) with number of characters which depends on the selected

encryption length.



TIME STAMP:

parameter for enabling alarm transmission complete with transmission date and time.

UT00:INSTALLER
TELEPHONE DIALER

TELEPHONE DIALER
GPRS PARAMETERS

GPRS PARAMETERS
APN

GPRS PARAMETERS
USER

GPRS PARAMETERS
PASSWORD

GPRS PARAMETERS
DNS1

GPRS PARAMETERS
DNS2

GPRS PARAMETERS
ACCESS NUMBER

Содержание MP500/16













































































































































Результаты поиска

Содержание MP500/16

Отзывы:

Elkron MP500/16, Руководство по программированию, Страница: 61 / 140

Результаты поиска

Содержание MP500/16

Отзывы: