manualshive.com logo in svg

Elkron MP500/16, Руководство по программированию, Страница: 27 / 140

Поделиться
Скачать
Elkron MP500/16 Скачать руководство пользователя страница 27

 

             MP500/4N-8-16 Programming  

27 

 

 
 

4 -  SYSTEM COMMISSIONING  

This chapter describes the programming needed to commission the burglar alarm system at the end of installation and to connect the 
various devices. 
 
Programming  may  be  carried  out  by  means  of  a  system  keypad,  a  service  keypad  (see 

Installation  Manual

  for  more  information  on 

connections)  or  a  PC provided  with  Hi-Connect  software  and  connected  to  the  control  panel  by  means  of  a  USB cable  and  optional 
interface (see 

Installation manual

 for more information on connections). 

 
The control panel may be programmed at a workshop and the programming may later transferred on site using a USB flash drive and 
optional interface. 
 
This  chapter  describes  the  programming  procedures  for  keypads  with  LCD.  The  programming  procedure  on  the  KP500DP/N  or 
KP500D/ST touchscreen keypad is the same but the information shown on the OLED may be slightly different. 

4.1 

CONVENTIONS USED IN PROGRAMMING PROCEDURES 

Programming is carried out using the keys and reading the messages and information which appear on the display.  
 
The main functions associated to the keys are:  
 

 

To access the menu  

 

Confirms the entered parameter, accesses the displayed submenu or confirms the selection made  

 

Goes back to the previous page or menu level  

 

Scrolls the menu items, edits a value  

 

Scrolls the menu items, edits a value  

 

Moves the cursor along the writing line   

 

Moves the cursor along the writing line  

 
The following step-by-step programming and configuration procedures show the keys to be pressed and what appears on the display. 
Text is limited to the essential minimum. The concerned function, the parameters to be configured, what the parameters are for and the 
possible values are described before each procedure. 
 

<Master code> 
<User code> 
<Technician code> 
<Technical Manager code> 

This indicates the code to be entered using the keypad. 

<Master  /  User  /  Installer  / 
Technical Manager code> 

This means that either code may be entered on the keypad indifferently. 

 
It is indicated whether each procedure is EN50131 grade 3 compliant or not. 

The indication is hierarchic: this means that an indication provided in a parameter applies to the parameter below it unless  otherwise 
indicated. 
 
 

Содержание MP500/16













































































































































Отзывы:

Нет отзывов