manualshive.com logo in svg

Elkron MP500/16, Руководство по программированию, Страница: 128 / 140

Поделиться
Скачать
Elkron MP500/16 Скачать руководство пользователя страница 128

128 

  MP500/4N-8-16 Programming                                                               

 

 

 

10.3  IDP MESSAGE STRUCTURE 

One message is sent for each single event. Several events will be sent in the same telephone call, if applicable.  
For  example,  messages  related  to  each  partition  concerned  by  an  arming  or  disarming  event  will  be  sent  in  sequence  in  the  same 
telephone call because the global system arming or disarming does not exist as an event. 
The message string structure is applicable for all events. 

 

A 

A 

A 

A 

1 

8 

Q 

E 

E 

E 

G 

G 

C 

C 

C 

S 

Rem.Ctrl Code 

FIXED 

Qualification 

Event 

Group 

Code or input ID 

Cks 

 

Where: 

 

Block 

Code 

Description 

Rem.Ctrl Code 

xxxx 

these are the last four digits of the remote control code  

Qualification 

1 

this indicates the beginning of an event or disarming  

3 

this indicates the end of an event or arming  

Event 

100 

emergency alarm from input  

101 

emergency alarm from function key on keypad  

110 

fire alarm from input  

111 

fire alarm from function key on keypad  

120 

panic alarm from input  

121 

hold-up alarm from input 

122 

silent panic alarm from input or from function key on keypad  

130 

hold-up alarm from input and way (route) input (entry / way / exit) 

137 

tamper input alarm   

138 

input pre-alarm 

145 

control panel and/or peripheral device tamper alarm  

150 

technological event 1 from input  

151 

technological event 2 from input  

152 

technological event 3 from input  

300 

failure alarm from failure input  

301 

lack of power alarm  

302 

low battery alarm 

307 

power failure alarm  

320 

siren failure  

330 

control panel bus communication to peripheral device error alarm  

344 

jamming alarm (in presence of radio expansion module only) 

351 

PSTN telephone failure alarm  

354 

GSM telephone failure alarm   

355 

no supervision alarm (in presence of radio expansion module with devices only) 

380 

detector failure  

388 

jamming  

401 

arming/disarming from user code, key, remote control   

403 

arming/disarming from timed programmer  

407 

arming/disarming from remote with DTMF code or Hi-Connect 

409 

arming/disarming from key input  

450 

arming with overriding  

454 

partitions  not  armed  because more than  70%  of  the  total inputs  are open  or  isolated in presence of 
faults, tampering  

458 

maintenance (installer working on site) 

461 

wrong code alarm 

570 

input isolation 

573 

input inhibition 

601 

manual test call  

602 

cycle test call  

Group 

00 

the event refers to the entire system 

01 ÷ 16 

the event is referred to partitions 1 - 16  

 

Table 16 - IDP message structure 

Содержание MP500/16













































































































































Отзывы:

Нет отзывов