Elkron MP500/16 страница 114 Скачать руководство пользователя | Manualshive

Страница: 114 / 140

background image

114

MP500/4N-8-16 Programming

8.3.3

How to save data on USB flash drive

Proceed as follows to save data on a USB flash drive:

1) Insert the USB flash drive in the USB - IT USB/KEY interface.

2) Enter

<Installer code>

, press

, then

and finally

repeatedly until MAINTENANCE

appears.

3) Press

and then

several times until DATA TRANSFER appears.

4) Press

. Press

and

to select SAVE SETTINGS. Press

to confirm.

5) Press

and

to select the data to be saved: CONFIGURATIONS, CODES/KEYS,

DIAGNOSE LOG. Press

to confirm. The folders will be automatically created by the control

panel if they are not already present on the flash drive.

6) A password will be required to save codes/keys. Enter the

< Master code>

.

7) The saving operation may take several minutes. The keypad will beep during the saving process

and the message “WAIT PLEASE” will be gradually replaced by “>”. At the end, the message
“CONFIGURATIONS OK” will appear if the operation is successful. Otherwise, “KO” will appear (other
references may appear if other data are saved).

IMPORTANT!

Never remove the key or disconnect power from the control panel while the

yellow LED of the USB/KEY interface blinking.

8) Press

.

9) Repeat from step 5 to save other data types.

10) Press

repeatedly to exit from the menu.

UT00:INSTALLER
MAINTENANCE

MAINTENANCE
DATA TRANSFER

DATA TRANSFER
SAVE SETTINGS

SAVE SETTINGS
CONFIGURATIONS

CONFIGURATIONS
WAIT PLEASE

«
...
112
113
114
115
116
...
»

Содержание MP500/16













































































































































Отзывы:

Нет отзывов

Похожие инструкции для MP500/16

Бренд: NCR Страницы: 6

Бренд: IFM Страницы: 49

Бренд: Taoglas Страницы: 2

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Бренд: PESA Страницы: 30

Бренд: Quickie Страницы: 108

Бренд: GARDINER TECHNOLOGY Страницы: 28

Бренд: Consort Страницы: 4

Бренд: FUTABA Страницы: 16

Бренд: Zennio Страницы: 2

Бренд: Ocean Breeze Страницы: 6

Бренд: Hydrotechnik Страницы: 42

Бренд: Ebyte Страницы: 22

Бренд: Mhouse Страницы: 44

Бренд: VECTOR CONTROLS Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды