Elkron ER500 Скачать руководство пользователя | Manualshive

Страница: 38 / 44

background image

38

Installation/Configuration ER600

11 - MAINTENANCE

The maintenance operations which do not require to operate physically on the system are described here.

11.1 HOW TO UPGRADE BUS DEVICE FIRMWARE FROM MENU

The firmware of bus devices can be upgraded from the control panels without needing to disconnect the devices or switch the system off.

The firmware is upgraded by connecting them to the bus.

IMPORTANT!

Firmware can only be upgraded if the Elkron Customer Care Centre has provided the necessary files and the

accompanying technical notes.

11.1.1

Necessary conditions

The upgrade procedure will only be started in the following conditions:



Devices are acquired and correctly operating in the system.



Devices are equipped with software release which can be upgraded (see table).



The files (“filename”.BIN) reside in the “MP500_4N\UPG”, “MP500_8\UPG” or “MP500_16\UPG” folder (only for device files; the
control panel file must reside in the root of the USB flash drive).



The firmware release of the upgrade file is different from the release residing in the device.



The IT USB/KEY interface is connected to the control panel.

IMPORTANT!

The IT-USB/KEY interface must be connected to the control panel when the latter is not powered (mains power

and battery disconnected).

Device

Upgradeable FW release

Device type

File name

ER600

V 1.00

Radio expansion

ER600.bin

11.1.2

Upgrade file

The upgrade files have extension “.bin”.
The filename is equal to the name of the device to be upgraded.

Example for MP500/16 control panels:

ER600 device

upgrade file ER600.bin

The files of the devices must be copied to the

MP500_16\UPG\

folder specifically created on the USB memory stick (USB flash drive

etc.).
The control panel file must be copied directly to the root of the USB memory stick (USB flash drive etc.).

Example

Device

File path on USB memory stick

ER600

MP500_16\UPG\ER600.bin

IMPORTANT!

Do not change name or path of the file: the control panel only recognises the set terminology. The file will not be

recognised if the file is renamed or the position is changed on the USB memory stick and the upgrading procedure will not be
started. Several files related to different device types or other files non-Elkron files may coexist on the same USB memory stick

«
...
36
37
38
39
40
...
»

Содержание ER500













































Отзывы:

Нет отзывов

Похожие инструкции для ER500

Бренд: B&B Electronics Страницы: 55

Zlinx ZP Series

Бренд: B&B Electronics Страницы: 70

Бренд: Garmin Страницы: 24

Бренд: Kenwood Страницы: 2

Бренд: Cobra Marine Страницы: 33

Бренд: Sandstrom Страницы: 92

Бренд: AUDIOLINE Страницы: 10

BTH-500-R Series

Бренд: Nextav Страницы: 8

Бренд: Com-Net Ericsson Страницы: 20

Бренд: Denver Страницы: 22

Бренд: SLIVE Страницы: 2

Бренд: Navman Страницы: 18

Бренд: Telefunken Страницы: 14

Бренд: Maximon Страницы: 27

Бренд: MPH Industries Страницы: 3

Бренд: BK Radio Страницы: 26

Бренд: BK TECHNOLOGIES Страницы: 71

Бренд: Datexx Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды