background image

 

16 

Replacing the light bulb 

Disconnect the hood from the electricity. 

Warning! 

Prior to touching the light bulbs ensure they are 

cooled down. 

Replace Lights  

•  Remove the damaged light (twist  counter clockwise) 

and replace with a new 120 Volt, 50 Watt (maximum) 
50° halogen light made for a GU10 base, 

suitable for 

use in open luminarie

 

 

 

Some models envisage lateral lamps: 

Replace them with identical forms of 40W (E12) max). 
Remove cover to access the lamp housing. 
If the lights do not work, make sure that the lamps are fitted 
properly into their housings before you call for technical 
assistance. 

 

Charcoal Filter 

It absorbs unpleasant odours caused by cooking. 

The charcoal filter can be washed once every two months 
using hot water and a suitable detergent, or in a dishwasher 
at 65°C (if the dishwasher is used, select the full cycle 
function and leave dishes out). 
Eliminate excess water without damaging the filter, then 
remove the mattress located inside the plastic frame and put 
it in the oven for 10 minutes at 100° C to dry completely. 
Replace the mattress every 3 years and when the cloth is 
damaged. 

  
 

 

Содержание Grace

















Отзывы: