Spring
Lever
Cradle Assembly
Brackets
Screw Used
(shown actual size)
2.6 x 6mm
X2
Plate
Big Washers
Screw Used
(shown actual size)
2.6 x 6mm Screws
with Washer
2.6 x 6mm with washer
X2
Input Modular Jack
Buzzer Pad
Remove
Backings
Modular Jack
PC Board
Buzzer
Screw Used
(shown actual size)
2.6 x 6mm Screws
2.6 x 6mm
X3
Index Label Shield
Index Label
Hook Switch
NOTE: Be
sure that the
Lever is above the
Hook Switch as
shown.
Lever
Decorative Piece
Push Button Panel
NOTE: Push
the Push Button
Panel up and
snap it into
position.
2.6 x 10mm Screws
Screws Used
(shown actual size)
2.6 x 10mm
X2
Handset Assembly
Speaker Pad
Remove
Backing
Speaker
Speaker Pad
Remove
Backing
Mute Button
Keypad Contact
Number
Button
Flash Button
Redial Button
3
2
1
6
5
4
9
8
7
#
0
*
Back View
Use this diagram as a
guide when installing
the number buttons.
NOTE: Make
sure that the angle
on the Flash, Redial,
and Mute buttons are
in the same
direction shown.
Keypad PC Board
Rubber Microphone Cup
Microphone
Screw Used
(shown actual size)
2.6 x 6mm Screws
2.6 x 6mm Screws
2.6 x 6mm
X6
2
5
3
4
Modular Jack
Wiring/Tubing Assembly
NOTE: Follow
these steps for
wiring the speaker
wires to the PC
board wires.
1
Screw Used
(shown actual size)
2.6 x 14mm Screws
Cut Tubing
Slide
Tubing
onto wire.
Twist
wires
together.
Slide
Tubing over
the twisted
wires.
2.6 x 14mm
X2
Wiring/Tubing Assembly
Coiled Cord
NOTE: When
snapping the receiver
cover on, start from the
back.
It may take a couple
attempts to attach
the two pieces.
Phone Number Shield
Phone Number
Label
2.6 x 14mm
Screws
Before the Final
Assembly
Refer to Pages 5 & 6 and perform the
Transmit/Receive & Dial Tests.
Screw Used
(shown actual size)
2.6 x 14mm
X2
Final Assembly
Foam Feet
Bottom View
Remove
Backing
T
H
IS
U
N
IT
C
O
M
P
L
IE
S W
IT
H
P
A
R
T
6
8 F
C
C
R
U
L
E
S F
C
C
N
O
.
G
X
A
1C
H
N
-7
44
12
-T
E
-E
R
E
N
N
O
. 1
.3
B
U
SE
S
T
R
A
N
D
A
R
D
J
A
C
K
U
SO
C
R
J1
1C
FCC Label
Line Cord
Copyright © 2005 Elenco
®
Electronics, Inc. All Rights Reserved. • 150 Carpenter Ave. • Wheeling, IL 60090 • (800) 533-2441 Fax: (847) 520-0085 • e-mail: [email protected] • Website: www.elenco.com
You have now completed the assembly of the AK-750 Telephone Kit. Refer to
HOW TO USE IT
on
the other side. If the phone does not work, refer to
TROUBLESHOOTING
.
There are many other projects: RC Car, Talking Clock, etc. Ask your store about these
projects or call at (847) 541-3800.
2.6 x 6mm Screws
Contact Elenco
®
Electronics if you have any problems. Actual colors may vary from those shown here.
ASSEMBLY INSTRUCTIONS
Side View
Top View
Hook
Switch
Lever
Bend LED’s up
1/8”
Use scissors
to cut off 1/8”.
AK-750/FUN-755
AK-750/FUN-755
Long Part of Spring
Short Part of Spring
NOTE: Remove any
burrs on the buttons
before installing them into
the Push Button Panel.
2
Remove Burrs
NOTE: This
may take a
couple attempts
to attach the two
pieces.
Remove
Screws Used
(shown actual size)
3 x 7mm
X4
3 x 7mm Screws
Cut-away View
Hook Switch
Lever
