Electrolux MAGISTAR OVEN 6-10-20GN Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 124

Electrolux MAGISTAR OVEN 6-10-20GN Скачать руководство пользователя страница 77

77

E.3

UI Level B, C (Digit)

If the user interface (user board) cannot communicate with any other board for more than a determinate time (for example 15 sec)
any running cooking cycle will be stopped. The error icon will show a message “

ECom

“. No cooking cycle can be launched till the

communication is established again.

CONNECTOR

FUNCTION

NOTES

BT1

BATTERY CR2032

DATE / TIME MEMORY

J1

PMACS

J1 IS CONNECTED TO ACU (POWER BOARD) X27.

Pins of J1:

= J1-1 = RS485 J1-2 = RS485 J1-3 = GND

J1-4 = +12V J1-5 = GND

J2

PMACS

see note

J3

ADDRESS

NOT USED / EMPTY

J4

ON / OFF

12V AND 0/1 SWITCH STATE

J5

USB

USB PORT

J6

NIU

FOR WIFI ANTENNA

J7

DEBUG

NOT USED / EMPTY

J8

BOARD PROGRAMMING

NOT USED / EMPTY

X21

COMMUNICATION CABLE

12V AND 0/1 SWITCH STATE

X19

PHASE 230V IN, CONNECTED TO C1.1 and C1.2 of EWD “SM“

RECOVERY

CONNECTED TO ACU (POWER BOARD) X28

NOTE!
The J1/PMACS can be connected to any X27 connection of the ACU. J1 vs J2 are interchangeable. X21 and X19 are
the numbering of the ON/OFF board, but also the ACU has the same numbering.

ACU-X27

BT1

J2

J1

J5

J6

J4

J3

J8

J7

X21

X19

J5

RECOVERY

ACU/X28

USER BOARD
(U.I)

O/I ON OFF
BOARD (SM)

«
...
75
76
77
78
79
...
»

Содержание MAGISTAR OVEN 6-10-20GN





























































































































Отзывы:

Нет отзывов