Electrolux 400 SERIES Скачать руководство пользователя

Страница: 49 / 52

PROBLEM

POSSIBLE CAUSES

SOLUTIONS

Washer does

not start

• Electrical power cord may not be

plugged in or connection may be

loose.

• House fuse blown, circuit breaker

tripped, or a power outage has

occurred.

• Action of pressing start/pause

button on “touch screen” style

console not recognized.

• Water supply faucets are not

turned on.

• Motor is overheated. Washer

motor will stop if overheated.

• Door may be open. Unit will not

operate with door open.

• Light next to start/pause button is

flashing indicating unit is paused.

• Make sure plug fits tightly in wall

outlet.

• Reset circuit breaker or replace

fuse. DO NOT increase fuse

capacity. If problem is a circuit

overload, have it corrected by a

qualified electrician. If problem is

a power outage, call local electric

company.

• Press start/pause button with bare

fingertip.

• Turn on water supply faucets.

• It will automatically restart after

a cool down period of up to 30

minutes (if washer has not been

manually turned off).

• Ensure door is closed.

• Press start/pause button to

continue the cycle.

WATER
Water collects in

folds of the door

gasket at the

end of the cycle

• This is a result of the washing

action and is part of the normal

operation of the washer.

• Wipe and dry the gasket to

remove water and any debris

remaining in the gasket after use.

Water collects

in bleach and

fabric softener

compartments

• This is a result of the siphoning

action and is part of the normal

operation of the washer.

• Water may be removed by

removing the dispenser drawer

(see

Care and Cleaning in this

manual) and draining water into

the empty drum or sink.

Wash load too

wet after spin

• Washer is overloaded.

• Load is too small.

• Load is out of balance.

• Drain hose is kinked.

• DO NOT overload washer. See

Operating Your Washer.

• Add 1 or 2 similar items to help

balance load.

• Rearrange load to allow proper

spinning.

• Straighten drain hose.

Water does not

enter washer or

it enters slowly

• Water supply is not adequate in

area.

• Water supply faucets are not

completely open.

• Water is being used elsewhere in

the house. Water pressure must be

at least 30 psi (260 kPa).

• Water inlet hoses are kinked.
• Water inlet screens plugged.

• Check another faucet in the

house. Wait until water supply and

pressure increase.

• Fully open hot and cold faucets.

• Avoid running water elsewhere

while washer is filling.

• Straighten hoses.
• Remove hose from inlets and

clean screens.

TROUBLESHOOTING

Содержание 400 SERIES





















































Результаты поиска

Содержание 400 SERIES

Отзывы:

Похожие инструкции для 400 SERIES

Бренды по названию

Популярные бренды

Electrolux 400 SERIES, Инструкция по использованию и уходу

Результаты поиска

Содержание 400 SERIES

Отзывы:

Похожие инструкции для 400 SERIES

Бренды по названию

Популярные бренды