Electrolux 400 SERIES Скачать руководство пользователя

Страница: 44 / 52

Rubber Washers

Must Be Present

Replace Hoses Every 5 Years

1. Turn off the water supply to washer

to avoid water leaks due to water

pressure surges and unforeseen

occurrences in the water supply.

2. Disconnect or unplug the electrical

power to the washer.

3. Remove excess water from the

dispenser, interior door and tub and

perform the Care and Cleaning steps.

1. Review the

Installation section of this

manual to ensure the appliance is level

and the water and electrical power

supply is properly connected.

2. Ensure the water lines are flushed of

debris, prior to connecting the water

lines to the washer inlet.

3. Check for water leaks and replace

supply hoses if needed.

Instructions for limited use,

vacation and away from

home

Reconnecting water supply

and electrical

Water inlet hose inspection

Periodically inspect all water inlet hoses

for water leaks, wear, cuts, corrosion and

bulges. Replace all hoses, if any sign of

the above is visible. All hoses should be

replaced every 5 years to reduce the risk of

hose failures. When replacing hoses, refer to

the Installation sections of this Use & Care

Manual for proper installation instructions.

DO NOT overtighten or cross thread the

fittings. DO NOT allow the hose to rub

against sharp objects. Always ensure the

hose fitting rubber gasket is installed and

free from water leaks when water pressure is

applied.

Grounding type wall receptacle

Power cord with

3-prong grounded plug

Do not, under

any circumstances,

cut, remove,

or bypass the

grounding prong.

CAUTION

Your washer should be operated

ONLY

when you are home. Water leakage is a

safety issue and can cause personal injury

or property damage. If you are away

from home or not using your washer for

extended periods of time, follow these

steps:

CAUTION

Damaged or improperly installed water lines

can cause the water lines or connections to

leak. Water leakage is a safety issue and can

cause personal injury or property damage.

IMPORTANT

When reinstalling the washer after

disconnecting the water supply lines and

electrical power, please follow the steps

below:

WARNING

Improper grounding of the washer may

cause serious injury or death. Check with a

licensed electrician if you are in doubt as to

whether the appliance is properly grounded.

CARE AND CLEANING

Содержание 400 SERIES





















































Результаты поиска

Содержание 400 SERIES

Отзывы:

Похожие инструкции для 400 SERIES

Бренды по названию

Популярные бренды

Electrolux 400 SERIES, Инструкция по использованию и уходу

Результаты поиска

Содержание 400 SERIES

Отзывы:

Похожие инструкции для 400 SERIES

Бренды по названию

Популярные бренды