Electrolab DLS 2100 Series Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 37

Electrolab DLS 2100 Series Скачать руководство пользователя страница 14

© 2020, Electrolab, Inc.

March 2020

Report Level and Temperature Continuously (Factory Diagnostics)

Uuu??
Response: Same as above, except continuously, with internal module configuration and
reported individual switch activation and groups of activated switches.

Note: The unit must be powered down before it will respond to other commands.

Report 4-20mA Output Level (Version 3.09 and Higher)

Uuu?M
Response: UuuMhhhhEeeeeWwwww
uu = unit number
hhhh = hex value 0x0000-0xFFFF eeee = error number

0 = No errors
1= No float detected
2 = One float is out of range on a two-float sensor
3 = Too many groups
4 = (reserved)
5 = Transmit to slave processor for level failed
6 = Transmit to slave processor for temperature failed
7 = Receive from slave processor of level failed
8 = Receive from slave processor of temperature failed
9 = No slave processors responding

Note: If errors 5 through 9 occur and persist after power cycling, the sensor should be
returned for repair.

wwww = warning number

0 = No warnings
1 = Possible level degradation
2 = Possible level degradation due to level offset

Report Temperature Only

Uuu?T
Response: UuuFxxEeeeeWwwww
xx= temperature

Configuration Commands

Assign Unit Number

UuuNnn
uu = unit number (from 00 to 31)
nn = new unit number

Note: Unit number 00 is not valid in Modbus RTU mode

Response: UuuNOK
uu = newly assigned unit number

«
...
12
13
14
15
16
...
»

Содержание DLS 2100 Series






































Отзывы:

Нет отзывов