Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 86

Страница: 86 / 322

Doc

E154713

4-14

4: Electrical Installation

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

4.5.5.3: D Low-Voltage Power Supply

CAUTION:

Note that the wiring for the D Option power supply has the

Positive and Negative terminals

REVERSED

from the 115AC and D2

models -

BE CAREFUL

to follow the diagram and instructions below.

For the D Option power supply:

1. Connect the negative voltage to the V(-) terminal.

2. Connect the positive voltage to the V(+) terminal.

3. Connect earth ground to the PE GND terminal.

Use a 4 Amp Slo-Blo fuse on the power supply, for example, UL approved Littelfuse
part number FLQ4.

1. Connect the
Negative Voltage
to V(-).

2. Connect the
Positive Voltage
to V(+).

3. Connect earth
ground to
PE GND.

Содержание Shark 100T



































































































































































































































































































































Результаты поиска

Содержание Shark 100T

Отзывы:

Electro Industries/GaugeTech Shark 100T, Руководство по установке и эксплуатации, Страница: 86 / 322

Результаты поиска

Содержание Shark 100T

Отзывы: