Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 322

Electro Industries/GaugeTech Shark 100T Скачать руководство пользователя страница 61

Doc

#

E154713

3-5

3: Hardware Installation

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

Electro

Industries/GaugeTech

The Leader In Power Monitoring and Smart Grid Solutions

3.3: Mounting Instructions

1. Slide the meter into the panel. Note that you can mount the meter either horizon-

tally or vertically (see figures 3.5 and 3.6).

2. From the back of the panel, slide 4 mounting brackets into the grooves on the top

and bottom of the meter housing (2 fit on the top and 2 fit on the bottom), if you
are mounting horizontally, or on either side, if you are mounting vertically (2 on
each side).

3. Snap the mounting brackets into place.

4. Secure the meter to the panel with lock washer and a #8 screw in each of the 4

mounting brackets (see figures 3.5 and 3.6).

5. Tighten the panel mounting screws with a #2 Phillips screwdriver. Do not over-

tighten. Maximum installation torque is 3.5 Lb-In.

NOTE

: If necessary, replacement mounting brackets (Part number E145316) may

be purchased from EIG.

«
...
59
60
61
62
63
...
»

Содержание Shark 100T



































































































































































































































































































































Отзывы:

Нет отзывов