ELECTRO FREEZE Soft Serve Model 30T-RMT
24
184952
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
123456789012345
5. (Refer to figure 7-4.) Install and
then lubricate the O-rings on the dispensing
plungers and insert by twisting each
plunger halfway into the head.
6. Install and then lubricate the 4-inch
head O-rings.
7. Position the handle(s) in the head
and ensure that the longest handle is in the
center plunger. Lock in place with the
handle pin.
8. Install and lubricate O-rings on the
air bleed plugs. Insert plugs in the head
assembly.
9. Lubricate the inside surface of the
cylinder bushing and place on the end of
the beater shaft.
Important:
ALWAYS make sure the cylinder bushing
is positioned properly. Operating the
freezer with a missing or badly worn
bushing will damage the beater, dispense
head and cylinder.
Important:
Excessive force will damage the head.
Do not use tools to tighten.
10. Install the dispensing head onto the
freezer by aligning the studs with the holes
in the head and sliding toward the freezer.
Tighten the hand knobs evenly, finger-tight
only.
11. Install the plunger rods. The nozzles
will be installed on the mix outlet at the
bottom of the dispense head after sanitizing.
-continued
Figure 7-4 Dispense Head Assembly
7
Assembly
(continued)