background image

© 

2015 eldoLED. All rights reserved. v1.3

More documentation and eldoLED’s terms and conditions are available at www.eldoled.com.

Pay attention when connecting the LED groups:
polarity reversal results in no light output and often damages the LEDs

 Wiring diagram POWERdrive 561/S, 561/A                   (PW0561S1, PW0561A1) 

 

WARNING: Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.

CAUTION: The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and build-
ing codes must be observed. Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.

LED outputs

R(ed) represents channel 1, G(reen) represents channel 2, B(lue) rep-
resents channel 3, and W(hite) represents channel 4. The default 
group colour allocation can be changed using the TOOLbox pro and 
freely available FluxTool application. 

Maximum wiring distance at full load (from LED driver to LED load):

 

LEDcode/NTC

The LEDcode/NTC interface allows connection of a 47k

Ω

 NTC therm-

istor for closed loop thermal control. The NTC throttle temperature is 
programmable through the freely available FluxTool software (see 
“Configuring your driver over DMX in”).

DMX in/DMX out

Connect the network cable’s DMX+, DMX- and DMX shielding wires 
to the corresponding pin or wire on the LED driver. 
For LED drivers that feature the WH0081S1 wiring harness, the wire 
colors on the harness and corresponding colors in a CAT 5 cable are 
listed in the following table.

The WH0081S1 wiring harness can be ordered from eldoLED.

Alternatively, if you wish to use a proprietary solution, the following 
molex parts should be used: 1x wire-to-board housing 87439-0800 
and 8x crimp terminal 87421-0000.

Configuring your driver over DMX in

Download the FluxTool software from your eldoLED driver’s product 
web page and connect a TOOLbox pro to DMX in to configure your 
driver. You can configure:
• various DMX parameters
• dimming curve
• minimum dimming level
• NTC throttle temperature
• LED drive current per output, from 200mA-1,050mA in 1mA steps

120-277V AC

The driver has been designed for use with universal mains voltage in-
put (120-277V AC, 50/60Hz), and for use with DC input (120-250V, as 
used in emergency lighting).

AWG value

20

19

18

17

16

Distance (m)

14

18

22

28

36

Distance (ft)

46

59

72

92

118

Please observe voltage drop over long cable lengths.

Longer cable lengths increase EMI susceptibility. 

For POWERdrive 561/A it is recommended to use shielded 
multi-core wires between LED driver and LED engine. Prop-
erly connect shield to ground on both sides. 

Wiring harness

CAT5 cable

DMX out shield

black 

brown

DMX out -

black/blue

orange

DMX out +

black/white

orange/white

DMX in shield 

black

brown

DMX in -

blue

orange

DMX in +

white

orange/white

120-277 VAC

L

N

4 LED outputs
4 control channels

1

9 mm

0.35 inch

Solid or stranded copper wires only.

0.5-1.5 mm

2

AWG 20-16

LED output 1

LED output 2

LED output 3

LED output 4

LEDcode/NTC

DMX out

DMX in

shield

-

+

shield

-

+

-
+

Отзывы: