background image

Technical Details

Frequency: 

868.0 MHz

Radiated power: 

0.49 mW

Modulation:  

FSK

Coding:  

Easywave A/B

Radio range:  

approx. 150 m in  

 

free field conditions

Detection angle: 

180°

Detection area: 

crosswise: max. 12 m  

 

frontal: max. 5 m

Installation height: 

2 m to 4 m

Creep-under protection: 

yes

Brightness setting range:  5 to 1000/∞ Lux

Switching period range: 

1 s to 20 min

Operating voltage: 

230 V AC, 

+10 % to15 %  50 Hz

Power consumption: 

0.8 W (standby)

Permissible ambient  

temperature: 

max. -25 °C to +45 °C

Protection class: 

II

Degree of protection: 

IP55

Dimensions (l/w/h):  

127/85/100 mm

Weight: 

220 g

 

Contact load:

Switching capacity: 

10 A   (cos

ϕ

 = 1.0) 

 

  6 A   (cos

ϕ

 = 0.6)

 

  3 AX (cos

ϕ

 = 0.3) 

Min. switching capacity: 

10 mA

Switching contact: 

µ-contact 230 V AC

LED lamps  >2 W <8 W 

  90 W

LED lamps  >8 W 

100 W

Incandescent and  

halogen lamp load:  

2,300 W

Low-voltage halogen

 

lamps: 

2,300 VA

Fluorescent lamps  

(low-loss series devices)   

     uncorrected: 

400 VA  

 

     series corrected: 

400 VA 

 

     parallel-corrected: 

400 VA (42 μF)

Fluorescent lamps:  

600 VA 

(electronic series devices) 

Compact fluorescent 

 

tubes: 

150 W

(electronic series devices)

SM01   Motion detector

GB

Function

The SM01 is a wireless motion detector and wi-

red motion detector for automatic lighting control 

based on movement and brightness. It is suitable 

for wall mounting outdoors. 
If a movement is detected while the measured 

brightness is below the set threshold value, the 

non-floating 230V relay output of the motion de

-

tector switches ON for the set time. 
In addition, a radio telegram (Easywave code A, 

ON) is transmitted, which can be taught-in to Ea-

sywave receivers. 
After the set time has elapsed, the relay output of 

the motion detector switches OFF and Easywave 

code B (OFF) is transmitted.
The device can be activated manually using a 

break switch. After releasing the button (voltage 

recovery), the device switches on (for at least 40 

seconds, or for the time set on the device).
The motion detector has two potentiometers on 

the underside of the sensor, which are used to ad-

just the time (minutes) and brightness (lux), etc.
The motion detector’s detection range is 12 m x 

5 m, with a detection angle of 180°.

 3 m

5 m

12 m

180°

6 m

2-4 

m

START UP
Mounting instructions 

-  The recommended mounting height is bet-

ween 2 metres and 4 metres.

-  The sensor reacts to changing heat radiati-

on. The motion detector should therefore not 

be mounted near heat sources, air currents 

or moving objects. 

-  Do not direct motion detectors at objects 

with highly reflective surfaces (e.g. mirrors, 

windows, etc.).

-  Obstacles (e.g. walls, glass panes etc.) do 

not radiate heat. 

-  Make sure that the wireless connection bet-

ween motion detector and receiver is unim-

peded. Avoid installing in the near of large 

metallic objects.

Scope of Delivery

Motion detector, base, drilling template, moun-

ting kit, operating manual

Intended Use

Only use the device as a motion detector for swit-

ching Easywave radio receivers or for switching 

directly connected electrical loads.
The manufacturer shall not be liable for any da-

mage caused by improper or non-intended use!.

Safety Advice

Before using the motion detector, care-

fully read through the operating instruc-

tions

Caution!

 

Electrical installation may 

only  be  carried  out  by  a  qualified 

electrician; otherwise there is a risk 

of electric shock or fire

Also note the operating instructions of the 

receiver(s)!

Do not make any modifications to the device!

Have faulty devices checked by the manufac-

turer

.

Only intended for installation out of arm‘s reach

.

Sensor

Potentiometer for set-

ting brightness (lux)

Potentiometer for  

setting time (min)

Model

SM01E5001A01

Отзывы: