background image

Model

  RTS43E5002A01         230 V

1

3

2

Mode

1

3

2

Mode

  RTS43E5002A02      12-24 V

Wall-mounted Transmitter   RTS43

GB

Technical Data

Frequency: 

868.30 MHz

Radiated power: 

max. 22.9 mW

Modulation: 

FSK

Coding: 

Easywave 

Power supply:

RTS43E5002A02  12-24 V AC/DC 
RTS43E5002A01     230 V AC  

(Connection cable:  

NYM-J min. 1.5 mm²)

Power consumption: 

Quiescent current 
12-24 V DC 

  6 mA 

   230 V AC 

10 mA

Transmission current
  12 V DC 

50 mA

  24 V DC 

27 mA

  12 V AC 

66 mA

  24 V AC 

39 mA

230 V AC  

12 mA

Protection rating: 

IP 65

Operating  

temperature: 

-20 °C to +60 °C

Range:  

typically 300 m with good

free field conditions

Dimensions: 

162x70x38 mm

Weight: 

200 g

Scope of Delivery

Wall-mounted transmitter RTS43, mounting kit, 

operating manual 

Intended Use

The wall-mounted transmitter RTS43 may only be 

used to operate Easywave wireless receivers.
The manufacturer shall not be liable for any da-

mage caused by improper or non-intended use!

Safety Advice

 Before using the device, carefully read 

through this operating manual! 

Caution! Electrical installation must only 

be carried out by a qualified electrician and 

only when there is no voltage present!

When the remote learning function is activa-

ted, the transmitter is live. Do not touch any 

live electrical parts.

When connecting the mains voltage supply 

with 230 V AC, an isolating protective device 

capable of disconnecting all poles must be 

present in the electrical circuit (e.g. automa-

tic circuit breaker 16 A).

The device is only intended to be securely 

mounted on a wall.
Note also the operating manual(s) for the recei-

vers!

Note  the  device-specific  standards,  VDE  and 

TÜV regulations!

Do not make any modifications to the device!

Have faulty devices checked by the manufac-

turer!

Jumper 

MODE

LED

PTx

Funktion

The RTS43 wall-mounted transmitter can extend 

the switching functions of existing switches or 

buttons using a wireless interface.
The transmitter checks whether the power has 

been coupled to a switch or button, and transmits 

the corresponding Easywave code A or B to an 

Easywave wireless receiver, which then activates 

a connected device. The LED indicates an outgo-

ing wireless signal.
Selecting the SWITCH or BUTTON mode is done 

using the Jumper MODE (see section “Select 

Mode”).
The default factory setting for the RTS43 is to 

connect a button (jumper position 1-2).

Start-Up

1. Screw on the housing cover and attach the

transmitter to the wall using the included

screws and wall plugs.

Avoid wireless interference. Avoid 

installing in a junction box, metal-

lic housings, in the immediate vi-

cinity of large metallic objects, on 

the ground or near these objects.

 

2. Select mode:

Button:   Jumper in position 1-2

Switch:   Jumper in position 2-3

3. Turn off the power supply to the circuit.

Connect the power supply cable and the

switch or button in a de-energised state in ac-

cordance with the connection examples (see

section „Connection examples“).

The terminals are designed for 

         

2x 2.5 mm² cable cross-sections. 

Use connecting cables such as 

  

NYM-J min. 1.5 mm². Disconnect the 

PE cable.

Insert all of the connecting cables into 

the device through the water-resis-

tant PG cable glands. After installati-

on, check the tightness of the device.

4.  Screw down the housing cover and switch the 

power supply back on.

5. Programme the RTS43 transmission codes

into the receivers of the devices to be cont-

rolled. By pressing the switch or button, the

transmission code is assigned to the receiver. 

Please also read the operating manuals for

the receiver.

Отзывы: