Elcometer 331 SH Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 72

background image

16

T

HE

MENUS

R

4.10 SELECT STATS

NO. OF READINGS . . . . . . . . Press Enter to toggle on or off
MEAN. . . . . . . . . . . . . . . . . . . Press Enter to toggle on or off
STD DEVIATION . . . . . . . . . . Press Enter to toggle on or off
COEF OF VARIAT’N  . . . . . . . Press Enter to toggle on or off
LOWEST READING. . . . . . . . Press Enter to toggle on or off
HIGHEST READING  . . . . . . . Press Enter to toggle on or off
UNDER RANGE. . . . . . . . . . . Press Enter to toggle on or off
BELOW LIMIT  . . . . . . . . . . . . Press Enter to toggle on or off
ABOVE LIMIT. . . . . . . . . . . . . Press Enter to toggle on or off
OVER RANGE . . . . . . . . . . . . Press Enter to toggle on or off
BLANK

k

. . . . . . . . . . . . . . . . . Press Enter to toggle on or off

Note:

Only two statistics from the above list can be toggled to ‘on’ at the same time.

4.11 SOUND MODE

LOCATE . . . . . . . . . . . . . . . . . Press Enter to toggle on or off
MAXPIP . . . . . . . . . . . . . . . . . Press Enter to toggle on or off
UNDER COVER. . . . . . . . . . . Press Enter to toggle on or off

Note:

Locate cannot be toggled to ‘on’ at the same time as either Maxpip™ or Under Cover.

4.12 UNITS

COVER . . . . . . . . . . . . . . . . . Press Enter, use Scroll keys to select units (mm/inch) and then

press Enter

TEMPERATURE . . . . . . . . . . Press Enter, use Scroll keys to select units (°C/°F) and then

press Enter

4.13 LIMITS

LOW LIMIT . . . . . . . . . . . . . . . Opens Low limit menu. . . . . . . . . . . See 4.18 LOW LIMIT
HIGH LIMIT . . . . . . . . . . . . . . Opens High limit menu . . . . . . . . . . See 4.19 HIGH LIMIT

4.14 CLOCK

l

TIME/DATE . . . . . . . . . . . . . . Use Scroll keys and Left/Right softkeys to set time and date

and then press Enter

SET DATE FORMAT . . . . . . . Opens Set date format menu . . . . . See 4.20 SET DATE FORMAT

4.15 OUTPUT

BAUD RATE. . . . . . . . . . . . . . Opens Baud rate menu . . . . . . . . . . See 4.21 BAUD RATE
RS232 BIT IMAGE . . . . . . . . . Press Enter to toggle on or off
RS232 PLAIN TEXT. . . . . . . . Press Enter to toggle on or off

Note:

RS232 Bit Image and RS232 Plain Text cannot be toggled to ‘on’ at the same time.

k.

‘Blank’ - available on Elcometer 331 Model TH only.

l.

‘Clock’ - available on Elcometer 331 Model TH only.

See “Sound mode/Detection mode” on page 33

See “Transferring readings to a computer” on page 52

331.book Page 16 Thursday, March 12, 2009 9:46 PM

«
...
18
19
20
21
22
...
»

Содержание 331 SH









































































Отзывы:

Нет отзывов

Похожие инструкции для 331 SH

Бренд: Keithley Страницы: 148

Бренд: Parker Research Corp Страницы: 3

Бренд: TANDBERG Страницы: 53

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

MIC TRAC MT-3000

Бренд: GAGEMAKER Страницы: 20

Бренд: K-Patents Страницы: 10

Бренд: Velleman Страницы: 96

Бренд: Cecomp Страницы: 4

Бренд: Det-Tronics Страницы: 18

Бренд: Guru Home Systems Страницы: 20

Бренд: LaserLiner Страницы: 52

Бренд: Kawai Страницы: 2

EA Heightmaster +

Бренд: PROLEC Страницы: 38

Photo Set Strato S-20

Бренд: Fisso Страницы: 2

Бренд: Fungilab Страницы: 47

Бренд: TESTO Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды