ELCOM Uniq 150, Руководство по обслуживанию, Страница: 19 / 41

30
Elcom, spoločnosť s ručením obmedzeným, Prešov Elcom, spoločnosť s ručením obmedzeným, Prešov
31
Uniq 150 Service manual Service manual Uniq 150
Needed to order Quantity Ord. code
Serrated lock washer M3 DIN6798 4 M250027
Barcode reader MS-1207FZY-1000R 1 —
2.13. Bluetooth and WiFi installation
2.13.1. Bluetooth installation
1. Put Bluetooth module to extension cord and metal part of module cover with insulation tape to prevent accidental
electric shortcut.
2. Extension cord end with Bluetooth put on rear hinge joint with two crossed ties.
I. It is necessaary to adjust extension cord if Bluetooth is installed into Tx execution:
a. Cut USB AM (male) connector from cable end and insulate wire ends.
b. Cable with connectors split to half and insulate wire ends.
c. Put tubing on those wires and solder cable on the extension cord.
d. Cover soldered places with tubing and shrink with hot air.
3. Other end of cable conenct to the mainboard connector:
Nx – to connector USB_C45 (N270) or USB1 (D525)
Tx – to connector USB01 (N270) or USB2 (D525)
4. (** only Nx execution.) Roll extension cord to provide optimal lenght and fix with tie.
Figure 2.13.1. – Bluetooth installation
8-wire cable – USB extension cord
2(7) –
4(5) –
6(3) –
8(1) –
black
green
white
red
1
Bluetooth cable adjustment for Tx execution:
Insulation tape
Rear hinge joint
Tie
USB extension cord
Bluetooth module
Needed to order Quantity Ord. code
Tubing 1,6 × 10 mm 4 * M010003
Cable 8-wires 250 mm 28 AWG 2H 1 * M200143
Tie EKB91N 2/3 ** M250009
Bluetooth USB key 1 M310015
USB extension cord AF/AM 1 m 1 M200141
* Consumes only half of cable and only in Tx execution!
** For Bluetooth installation in Nx executin will be used one more tie.
2.13.2. WiFi installation into hinge
Installation of WiFi antennas into hinge connectors module is performed if aluminium covers are not adjusted to
such installation (covers has not milled cavity for antennas setup).
1. Shrink tubing using temperature 240°C to diameter about 5 mm.
2. Put shrinked tubing on the antenna, warm it using temperature 140°C and flatten tubing.
3. Split doublesided tape lenghtwise and stick those pieces one on another to provide bigger thickness. Stick tape to
the antenna. Note that copper antenna side with its wire is on the another side as doublesided tape is!
4. Prepared antenna stick into the hinge.
5. Screw adapter to WiFi module.
6. Connect WiFi module with adapter to miniPCI connector CN4 (N270) or CN1 (D525) of mainboard.
7. Antennas cables connect to MAIN and AUX connectors of WiFi module.
Figure 2.13.2. – WiFi installation into hinge
Connectors module
sticked WiFi antenna
in shrinked tubing
Needed to order Quantity Ord. code
Doublesided sticker tape 15 mm 2 × 50 mm M990091
WiFi PCB antenna L = 400 mm
2,4G PCB antenna L=400mm
2
2
M310022
M310144
WPER-101GN(BT) mini PCIe WiFi module
Wifi interny s BT mPCIe WPEA
1
M310023
M310122
Intel 6235 wifi s BT mPCIe 1 M310111
Mini PCIe full size card 1 M310024
Screw of MiniPCIe card adapter 2 M310025
Tubing 9 mm 2 × 55 mm M010017