ekwb EK-PRO GPU WB RTX A100 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 13

ekwb EK-PRO GPU WB RTX A100 Скачать руководство пользователя страница 11

- 11 -

For this Step, you will need:

M3x6
SCREW

CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES

If necessary, temporarily remove the water block to check for uniform
surface contact between the block and components. Pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check
again or contact our support service at
https://www.ekwb.com/customer-support/.

Screw M3x6 DIN 7991

(2x) 9029

Allen Key 2mm

(1x) 8901

STEP 4c

STEP 4c

Fasten a inox power adapter to the water block with two M3x6

screws. The power cables is needed to be twistand bend a bit in

order to fit them in.

«
...
9
10
11
12
13
»

Содержание EK-PRO GPU WB RTX A100














Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды