background image

 
AD DRYER 

 

 

06/2022 

43 

NP-DK50-Nx2VTM-ADM-EN-1_06-2022 

20.4.  Service menu screen 

 

 

The service menu is intended exclusively for 
service personnel. Access to individual menu 

items is password (1992) protected. 

21. INDICATION OF MAINTENANCE AND ALARM STATES 

The  adsorption  dryer  controller  is  capable  of 
measuring  selected  parameters  (pressure 
and pressure dew point in versions with a dew 
point  sensor)  and  for  assessing  the  basic 
dryer operating states. 

Based  on  the  measured  parameters  and 
service  details,  the  controller  displays 

information  on  faults  using  the  following 
notifications and warnings. 

 

The  compressor  beacon  does 
not  light  up  in  the  event  of  a 
fault in the adsorption dryer! 

 

21.1.  Notification 

– Upcoming service interval 

 

  100  operating  hours  prior  to  the  next  service  interval

  a  yellow 

notification appears (“Notice!”). The service tile also lights up 
orange. 

 

The  remaining  hours  to  the  next  service  interval  are  also 
displayed. 

 

The  warning  is  shown  until  service  is  completed  and  the 
service interval is reset. 

21.2.  Warning 

– Service interval exceeded 

 

 

A red warning is shown (“Warning!”) once the service interval 
has lapsed. The service tile also lights up red. 

 

The  warning  is  shown  until  service  is  completed  and  the 
service interval is reset. 

 

The hours to the next service interval are also displayed. 

 

A list of warnings is saved in the “Warning log” 

  The dryer continues operating normally 

Содержание DK 50 4X2VT/M





























































Отзывы: