EKE-Electronics EKE-Trainnet AIM2505A Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 50

EKE-Electronics EKE-Trainnet AIM2505A Скачать руководство пользователя страница 13

Installing the AIM module into a rack

13

AIM2505A Technical Manual V2.03

3. Installing the AIM module

into a rack

This chapter includes instructions on how to install the EKE-Trainnet® AIM module
into a rack.

The following topics are covered in this chapter:



Before the installation



Installation procedure



Potential problems in installation procedure

Before the installation

3.1.1 Warnings

This section contains warnings you need to consider before and during the AIM
module installation.

Do not turn on the rack power before you have finished the
installation of the rack.
Never remove the AIM module from a rack. Always turn OFF the rack
power first BEFORE removing the rack.

Electrostatic discharge can damage electronic circuits. Always handle
the module at a static free workstation. If this is not possible, ground
yourself using a wrist strap and a resistive connection cord.

The module and also the rack can contain sharp edges. Use
protective clothing (gloves etc.).
Do not drop the module.

Make sure that the module or any of the components on it do not get
wet.
When handling the module, only touch the front panel. Do not touch
the board or any of the components on it. Even when you are
removing a defective module and sending it to maintenance, handle
the module according to these instructions.

«
...
11
12
13
14
15
...
»

Содержание EKE-Trainnet AIM2505A



















































Отзывы:

Нет отзывов