Eizo SCD 19102 Скачать руководство пользователя страница 47

Страница: 47 / 104

Commissioning

7.3 Description of OSD menu

SCD 19102 / SMD 19102
Instruction Manual, 05/2008, A5E01588521A-002

Main menu

Function

Adjustment/range

Description

DPMS setting
DPMS

On
Off

Default: On

The DPMS (Display Power

Management System) can

be switched on/off
When the DPMS is activated

and there is no input signal,

the backlight is switched off

or darkened (depending on

the parameter for the "DPMS

Off mode": see below).

This saves power, and

increases the service life of

the backlight.

DPMS Off mode (backlight)

Dimmed
Off

Default: Dimmed

"DPMS Off mode" can be set

to "Dimmed" or "Off". The

backlight is then either

dimmed or switched off when

the DPMS mode is active.

LUT choice
LUT backlight command

On / Off

Default: On

Permits access to the

backlight

•

When "On" is selected,

the backlight cannot be

changed in the

"Brightness/contrast"

menu.

•

When "Off" is selected,

the backlight can be

changed in the

"Brightness/contrast"

menu.

Select display function

1 ... 5

Default:

SCD 19102: LUT 1

Selection of display function:

information on the selected

curve
For further details on LUT

settings, see "Display

adjustment –

LUT" (Page 60).
The LUTs that can be

selected are displayed in the

table in the OSD menu.

Содержание SCD 19102









































































































Результаты поиска

Содержание SCD 19102

Отзывы:

Похожие инструкции для SCD 19102

Бренды по названию

Популярные бренды

Eizo SCD 19102, Инструкция по эксплуатации

Результаты поиска

Содержание SCD 19102

Отзывы:

Похожие инструкции для SCD 19102

Бренды по названию

Популярные бренды