Eighteeth E-connect S Скачать руководство пользователя страница 42

Страница: 42 / 47

12 EMC

Tables

12.EMC Tables

Guidance and manufacturer’s declaration – electromagnetic emissions

The

E-connect S

is intended for use in the electromagnetic environment specified below.

The customer or the user of the

E-connect S

should assure that it is used in such an

environment.

Emissions test

Compliance

Electromagnetic environment - guidance

RF emissions

CISPR 11

Group 1

The

E-connect S

uses RF energy only for its

internal function. Therefore, its RF emissions are

very low and are not likely to cause any

interference in nearby electronic equipment.

RF emissions

CISPR 11

Class B

The

E-connect S

is suitable for use in all

establishments, including domestic establishments

and those directly connected to the public

low-voltage power supply network that supplies

buildings used for domestic purposes.

Harmonic

emissions

IEC61000-3-2

Class A

Voltage

fluctuations/flicker

emissions

IEC 61000-3-3

Complies

Guidance and manufacturer’s declaration – electromagnetic immunity

The

E-connect S

is intended for use in the electromagnetic environment specified below. The

customer or the user of the

E-connect S

should assure that it is used in such an environment.

Immunity test

IEC 60601 test

level

Compliance level

Electromagnetic

environment - guidance

Electrostatic

discharge (ESD)

IEC 61000-4-2

+/- 8 kV contact

+/- 2 kV, +/- 4 kV,

+/- 8 kV, +/- 15 kV

air

+/- 8 kV contact

+/- 2 kV, +/- 4 kV,

+/- 8 kV, +/- 15 kV

air

Floors should be wood,

concrete or ceramic tile. If

floors are covered with

synthetic material, the relative

humidity should be at least

30 %.

Page 42 / 47

Содержание E-connect S
















































Результаты поиска

Содержание E-connect S

Отзывы:

Бренды по названию

Популярные бренды

Eighteeth E-connect S, Руководство пользователя

Результаты поиска

Содержание E-connect S

Отзывы:

Бренды по названию

Популярные бренды