Efka AB600A5015 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 64

background image

- AB600A5015

Instruction Manual

- 22 -

7.4 Unlocking the Chain (Mode 5/6/7)

Function

Parameters

Number of run-out stitches when unlocking the chain
Function “unlock the chain” in modes 5, 6 and 7

(c6)

(mEk)

184

190

Upon unlocking the chain at the seam end, the functions

thread trimming

and tape cutter/fast scissors are

automatically suppressed. When setting parameter

190 = 3

, the function

tape cutter/fast scissors

is however

possible. After pressing the key "unlocking the chain" and with pedal in position 0 (neutral), the drive always
stops in position 1.

Settings necessary for the operation “unlocking the chain”:



Set “unlock the chain” using parameter

190 =1 / 2 / 3 / 4

(

190 =0

“unlock the chain” off)



Set

switch-on delay

using parameter

181

and

reversing angle

using parameter

180



Determine the

function of the key “unlock the chain”

using one of the parameters

240...246



If parameter

290

is set at“

190 =0

Unchaining switched off

190 =1

Sequence with pedal in position -2 from machine run or from position 2:

-  Press key "unlock the chain"
-  Run at positioning speed to position 1
-  Sequence of reversing angle at positioning speed after a switch-on delay that can be set

190 =1

Sequence with pedal in position -2 from standstill in position 1:

-  Press key "unlock the chain"
-  Run at positioning speed to position 1
-  Sequence of reversing angle at positioning speed after a switch-on delay that can be set

190 =2

Automatic sequence with light barrier at the seam end without tape cutting / pedal in
position

–2 according to the setting of parameter 019

-  Press key "unlock the chain"
-  Run to position 1 after light barrier sensing
-  Sequence of reversing angle at positioning speed after a switch-on delay that can be set

190 =3

Automatic sequence with light barrier on the seam end with tape cutter and run-out
stitches(Only possible in mode 7 and if parameter 018 =0 )

- Press key "unlock the chain"
- After light barrier detection, sequence of the compensation stitches and end count up to tape

cutting

- Run-out stitches up to unlocking the chain, adjustable with parameter 184
- Sequence of reversing angle at positioning speed after a switch-on delay that can be set

190 =4

Sequence with pedal in position

–2 / no unlocking of the chain if seam end with light

barrier, cutting and run-out stitches is set:

-  Press the pedal to position -2
-  Run at positioning speed to position 1
-  Sequence of reversing angle at positioning speed after a switch-on delay that can be set
-  No unlocking of the chain at the seam end with light barrier
-

Reverse motor rotation is suppressed when the drive stops. The signals “blow fabric onto stack”,
M2 and “sewing foot lift” will be issued.

«
...
20
21
22
23
24
...
»

Содержание AB600A5015

































































Отзывы:

Нет отзывов

Похожие инструкции для AB600A5015

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: Samson Страницы: 52

Бренд: Samson Страницы: 32

Бренд: Danfoss Страницы: 59

Бренд: CAME Страницы: 98

Бренд: CAME Страницы: 16

Бренд: CAME Страницы: 8

Бренд: Hanwell Страницы: 34

Бренд: HANSONG Страницы: 11

Бренд: Datapath Страницы: 12

Бренд: Hansen Страницы: 4

Бренд: Walimex Pro Страницы: 68

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: jcm-tech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды