EFI Fiery ES IC-418 Скачать руководство пользователя страница 67

Страница: 67 / 243

Introduction

Printing describes how to install the printer drivers on Windows and Mac OS computers for the Fiery

ES IC-418.

This document covers the following topics:

•

Installing printer drivers on Windows computers

•

Setting up the printing connections on Windows computers

•

Printing from Windows computers

•

Installing printer drivers on Mac OS computers

•

Setting up Mac OS computers for printing

•

Printing from Mac OS computers

•

Fiery

ES IC-418 print options

•

Using printing methods other than the printer driver to print to the Fiery

ES IC-418

For information about setting up network servers and client computers to use the Fiery

ES IC-418, see

Configuration and Setup

. For general information about using the printer, your computer, application software, or

network, see the documentation that accompanies those products.
For information about supported operating systems and system requirements, see

Configuration and Setup

Terminology, conventions, and documentation resources

This document uses the following terminology and conventions to refer to the Fiery

ES IC-418, printer, and

supported operating systems.

Term or convention

Refers to

Aero

Fiery ES (in illustrations and examples)

Command WorkStation

Fiery Command WorkStation

Printer

MFP

Fiery ES

Fiery

ES IC-418

Mac OS

All supported Mac operating systems. For a complete list, see System Requirements in

Configuration and Setup

Windows

All supported Windows operating systems. For a complete list, see System Requirements in

Configuration and Setup

Printing

Introduction

Содержание Fiery ES IC-418




















































































































































































































































Результаты поиска

Содержание Fiery ES IC-418

Отзывы:

EFI Fiery ES IC-418, Конфигурация и настройка, Страница: 67 / 243

Результаты поиска

Содержание Fiery ES IC-418

Отзывы: