EFI E-36A Скачать руководство пользователя страница 34

Страница: 34 / 129

Installation and Service Guide: Color Controller E-36A

Using the E-36A

Overview of Fiery QuickTouch menu options

The following options are available from the Fiery QuickTouch main menu:

Figure 13:

Fiery QuickTouch Home screen

The Home screen is the main interface for job status, and displays various screen elements.

The Queue job list shows queued jobs and detailed information about each job.

E-36A name and status

Pressing the Fiery icon shows more information
about the E-36A and the network address.

Number of pages and copies that are printing

Icon of the print job type

If there are no print jobs being processed, an Idle
status displays.

Queued jobs list

Pressing the Queue icon shows a list of jobs that are
queued.

Printing progress of the active print job

Printed jobs list

Pressing the Printed icon shows the printed jobs list.

File name of the active print job

Quick Launch

The Quick Launch button displays additional
applications.

Time left to complete the active print job

Shows consumables

Quick Options and current local time

Содержание E-36A


































































































































Результаты поиска

Содержание E-36A

Отзывы:

EFI E-36A, Инструкция по установке и обслуживанию, Страница: 34 / 129

Результаты поиска

Содержание E-36A

Отзывы: