Edwards nEXT200200 Скачать руководство пользователя страница 29

Страница: 29 / 100

If the power limit setting is not adjustable, use a power supply capable to supply

sufficient current to meet manufacturer's factory default power limit setting shown in

Table: Logic interface technical data on page 27

The manufacturer's TIC has variants. If the pump is operated using the

manufacturer's TIC, contact us to select the applicable variant for the application.

3.7 Pumping media

WARNING: DANGEROUS GASES

Risk of asphyxiation. Release the dangerous gases and gas mixtures safely. Do not

expose people to the gases. If hazardous gases or vapour must pump, obey the safety

recommendations of the supplier of the gas or vapour.

WARNING: PYROPHORIC OR EXPLOSIVE GASES

Risk of explosion. Do not use the nEXT pump to pump pyrophoric or explosive gas

mixtures as the pump is not applicable for this purpose. The pump and its

connections are not designed to contain an explosion.

WARNING: DANGEROUS GASES

Risk of damage to equipment. In the interstage and booster versions of the

nEXT pumps, gas pumped through the interstage port will mix with gas pumped

through the pump inlet. Make sure that the gases do not react or combine to form

dangerous gases and substances.

WARNING: HIGH OPERATING PRESSURE

Risk of damage to equipment. Do not exceed the maximum continuous operating

pressure. Failure to do so can cause dangerous rotor temperatures and will decrease

the life of the pump.

WARNING: VACUUM EXPOSURE

Risk of injury. Do not expose the part of the human body to the vacuum.

WARNING: MERCURY VAPOUR

Risk of damage to equipment. Do not use a nEXT pump to pump mercury vapour. Do

not allow mercury (for example, from a McLeod gauge) to come in contact with the

pump. If mercury vapour is pumped, the pump rotor can corrode and fail.

Note:

Concentrations of gases can be changed by the compression of the pump.

The pumps are designed to pump the residual gases used in high

‑

vacuum systems are:

▪

Air

Page 25

B85200880_D - Technical data

Содержание nEXT200200





































































































Результаты поиска

Содержание nEXT200200

Отзывы:

Бренды по названию

Популярные бренды

Edwards nEXT200200, Инструкция по эксплуатации

Результаты поиска

Содержание nEXT200200

Отзывы:

Бренды по названию

Популярные бренды